Question about Blueant Z9 Wireless Headset

1 Answer

I am trying to pair my z9 with my nokia n95

These have been paired before but I havnt used them for a while. When the phone sees the z9 is pairs then asks for a password, have never come across this before and the devices are exactly ones paired before
Please help me I am driving to Toowoomba tomorrow 4 and half hour drive so it need it to be working

Posted by on

  • Dawn Feb 28, 2009

    Thanks its working now. Next problem I have a blueant supertooth and the same problem and suggestions

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 34 Answers

  1. Delete the old Z9 pairing
  2. With the Z9 OFF, Press and Hold the MFB for about 6 seconds. The LED will appear a solid Blue, and then will start flashing. The Z9 is now in Pairing mode and ready to be found in searches by other Bluetooth devices. Pairing mode will be active for 2 minutes
  3. Enter Passkey "0000" when your phone prompts you. The phone and Z9 will now Pair

I hope that helped.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cannot pair my iphone with blueant


The typical setup with a Bluetooth is press whatever the main button on the device is until there is a glowing blue light (usually about 3-6 seconds). You then need to go to the Bluetooth menu on the phone (under settings). Select scan for devices. After a few seconds, you should see Blueant Z9. Select it. it will then ask for pin to pair device. It should be either 0000 or 1234. After that, you should be all done.

May 04, 2011 | Blueant Z9 Wireless Headset

1 Answer

Clear memory on blue ant z9


  1. To reset your Z9i it must be switched on but not connected to any devices.
  2. You should already have deleted the pairing information from your phone, but if you have not, use your phone's Bluetooth menu to disconnect from the Z9i and delete the pairing information.
  3. Now reset the Z9i by holding down "Vol +" and "Vol -" and then clicking the BlueAnt button.
  4. The Z9i will refresh its memory, delete all current pairing information and automatically go into pairing mode.

Mar 02, 2011 | Blueant Z9i Bluetooth Headset

1 Answer

Can't pair Z9 with my blackberry 8120


Turn off your Z9
Turn the bluetooth feature ON on your 8120
Start the search for the bluetooth device
When the search starts, press and hold your ANT logo-button for about 6 seconds on your Z9.
First it will light up blue then starts flashing continuously.
Your phone should find it now with no problem!
Good Luck!

Sep 24, 2009 | Blueant Z9i Bluetooth Headset

2 Answers

I can't get my new iphone to pair with my BlueAnt.


Go to this page, it will answer any question concerning the blueant .. including pairing to your phone .. activating your blueant etc http://www.blueant.com.au/index.phpalso gives you step by step instructions on codes, pairing etc

Aug 12, 2009 | Blueant Z9 Wireless Headset

1 Answer

I cannot remember how to pair BlueAnt bluetooth to new devices


You will need to set the Z9 into pairing mode before your iPhone will find it.

The manual for the z9 is here

With the Z9 OFF, Press and Hold the MFB for about 6 seconds. The LED will appear a solid Blue, and then will start flashing. The Z9 is now in Pairing mode and ready to be found in searches by other Bluetooth devices. Pairing mode will be active for 2 minutes.

Enter Passkey "0000" when your phone prompts you. The phone and Z9 will now Pair.

Mar 10, 2009 | Blueant Z9 Wireless Headset

1 Answer

Pairing z9


Pairing Procedure
This is an example only and may differ from your phone, but the process will be the same.

With the Z9 OFF, Press and Hold the MFB for about 6 seconds. The LED will appear a solid Blue, and then will start flashing. The Z9 is now in Pairing mode and ready to be found in searches by other Bluetooth devices. Pairing mode will be active for 2 minutes.

Perform a Bluetooth device discovery on your mobile phone to add a new device.

Enter Passkey "0000" when your phone prompts you. The phone and Z9 will now Pair

Jan 29, 2009 | Blueant Z9 Wireless Headset

1 Answer

I cannot pair my Nokia N95 with HBH-608 Akono headset


Press and hold down the headset volume key in the centre. Hold it for about 5 sec. The led will now flash on/off in red. This is the pairing mode. Set your mobile phone to blue tooth discovery mode,until it finds the headset, key in the pass key, 0000. It should now work. You may need to set the phone to select the headset as an automatic connection so it connects whenever it is on and in range.

Jul 15, 2008 | Sony Ericsson HBH-PV705 Headset

1 Answer

I cannot pair my Nokia N95 with HBH-608 Akono headset


1)Turn on the blue tooth headset
2)Turn on bluetooth on your phone and search for devices.
3)When it finds the device select it and click connect.
Thats all.

Jul 14, 2008 | Sony Ericsson HBH-610a (Auto Pairing)...

1 Answer

Trying to pair device with the Nokia N95


The N95 has some compatability problems, i.e. it will pair with my newer Nokia CK-7W car kit but not with my older CK-1W car kit.

Nov 19, 2007 | Jabra BT150 Wireless Headset

Not finding what you are looking for?
Blueant Z9 Wireless Headset Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blueant Headsets Experts

Iron
Iron

Level 3 Expert

3018 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

aliasger yq

Level 2 Expert

213 Answers

Are you a Blueant Headset Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...