Question about Smoothfitness Smooth 5.45 Folding Treadmill

Open Question

Smooth fitness 5.25 treadmill not running...company sent new relay board...still not running. Is there some place to find wiring diagram to see if wired properly...or could something else be problem

Posted by on

4 Suggested Answers

  • 1 Answer

SOURCE: Wiring diagram need for an Smoothfitness EVO treadmill.

Solved this problem by contacting the Evo/Smooth directly. Great service.

Posted on Oct 20, 2009

ercupa190
  • 12223 Answers

SOURCE: i need a wiring diagram for a smooth fitness 5.45

You can try to nexts web pages:

1) http://fitness.manualsonline.com this is free download

2) www.fitnessrepairparts.com you must pay.

3) htp://manualsfactory.com you must pay.

4) www.pdfusermanual.com free download.

sincerely.

Posted on Nov 07, 2011

ercupa190
  • 12223 Answers

SOURCE: Smooth fitness treadmill beeps every two minutes

Walk on a treadmill to calculate distance.
Most electronic treadmills allow you to program for an alarm or beep when you've walked a certain distance.
Try to turn off reading your owner manual.
And check if there are some error code?.

If you do not have owner manual go to this web:
http://www.smoothfitness.com/support/product-manuals.htm
and download free.
sincerely.

Posted on Nov 22, 2011

ercupa190
  • 12223 Answers

SOURCE: need wiring diagram for a smooth 5.45 treadmill

http://www.smoothfitness.com/support/product-manuals.htm

GO TO THE WEB PAGE FROM SMOOTHFITNESS SECTION PRODUCTS MANUAL, GIVE YOU MODEL, SERIAL NUMBER AND DOWNLOAD FREE IN PDF FORMAT. AND READY.

GOOD LUCK.

SINCERELY.

E.CUADRA
MANAGUA, NICARAGUA. C.A

Posted on Nov 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bladez prisma treadmill error e1 replaced lower control board and speed sensor


I will answer my own problem here, maybe it will help someone else. After BH North America customer service told me I needed a new lower control board and I had to spend $100+, it wasn't the board. Then they said it was the speed sensor, they sent that out for free, that wasn't it. Now, they would not respond to me. So, we went off the troubleshooting guide saying it was a connection problem between the upper and lower board. My husband opened up the "leg" of the treadmill and checked the connections (cutting the tie cords that hold the wires tightly in place, maybe too tightly and that's what caused them to come unplugged) and now the belt runs! So, BH got another 100 dollars of my money, on top of the original $800 and solved nothing and then ignored my emails. Horrible customer service and when this one finally bites the dust, I will never purchase a machine from them again. P.S. This treadmill is only approx. 2 yrs old.

Feb 12, 2013 | Bladez Fitness Prisma Supra Folding...

1 Answer

Im fitting a new pcb board in my york t13i the upper board the incline has gone has the lights on it are not working ive taken the wires off the up down and cpu terminals but i cant remeber which way the...


please remember the wires before. wires again the old board, and make a wiring diagram. After you did , you must try again with the new board, and repeat the process, very Important.
If the problem persist, call to the supplier board, and tell them if the can send some wiring diagram, or see if with the new board there are some schematic wiring diagram. Otherwise, you must make some errors and additional problem you will find it.Contact them inmediately.
God bless you

Nov 22, 2012 | York Barbell Home Use Fold-Up Treadmill

1 Answer

I want to know what is a control processor and main processor for lifefitness treadmill 9100 and where it is located at. thanks


1_ CPU is SYSCON, is the unit control electronic,that sen all electronical signal to the electronic of equipment.
2) tight every wires connector very well and clean it
3) Run the software calibration for diagnose, troubleshooting , fix it
4) However you must calibrate the REED swith, see the diagram, clean it, and tigh the wires connector very well, exchange the batteries by new ones and clean the contacts cleaner 5) tight the ribbon cables from keypads switch +tight the display board connector vs lower board and proof again.
God bless you

7_27_2012_12_14_06_pm.gif7_27_2012_12_14_27_pm.gif

Jul 26, 2012 | Life Fitness 9100 Next Generation...

1 Answer

I have star trac pro treadmill,when i shifted from another place it show the error


1) Run the software calibration for diagnose, troubleshooting.
2) However adjust the reed switch, clean, and tight any wires connector see the diagram
3) adjust the speed sensor, clean, and tigh the wires connector see the diagram attached.
7_7_2012_11_09_43_am.gif7_7_2012_11_09_59_am.gif7_7_2012_11_10_22_am.gif

Jul 06, 2012 | Startrac Fitness Products Star Trac Pro S...

1 Answer

Buckmanservices.com fixed my treadmill it had the E1 error code. they are an online fitness diagnosis company


1) No there are NOT.
2) You must proceed trying to adjust the speed sensor, see the diagram attached, clean, and tigh the wires connector very well.
3) Measure the input voltage motor, if there are the motor need repair
4) Measure the output voltage board, for input voltage motor, if there are NOT the board is faulty.
see the diagrams attached.
6_14_2012_7_29_30_pm.gif6_14_2012_7_30_01_pm.gif6_14_2012_7_30_17_pm.gif6_14_2012_7_30_53_pm.jpg

Jun 13, 2012 | Proform Treadmills

1 Answer

I have a vision fitness treadmill T9250 and now the console display isn't working properly. Some of the


Dear Sir:

Please see the diagram attached from REED switch, adjust, clean, and tight the connector wires very well.

2) change the batteries by new ones, use the best.clean the contact batteries.

3) tight the ribbon cable from keypad .+ tight the connector from display board vs lower board.

4) after you fix it RUN THE sofware calibration for diagnose, troubleshooting, See my personal tips for help

sincerely. God bless you
5_3_2012_12_57_12_am.gif

Apr 30, 2012 | Vision Fitness T9250 Deluxe Folding...

1 Answer

Schmatic for digital concept board bklb375-4


Dear Sir:

As you must know, No factory or dealer want to giveen the schematic or wiring, or block diagram for non-person has not training for any factory or company for treadmills fitness.
They provide only information for owner or user manual. or parts manual.

However you will find that some company such as provide you , TO BUY some service manual.

Here is: www.fitnessrepairparts.com contact them, and Good luck.

However, I am attache my own block diagram that I did for persons like you for basic undertanding. I hope that this will be help you. Sincerely. Merry Christmas.

erensto cuaddra
managua, nicaragua.


12_19_2011_7_00_01_pm.gifnotese: I have schematic, wiring diagram, for my own service. If you want to get,it. contact me.sincerely

Dec 17, 2011 | Treadmills

2 Answers

I need a wiring diagram for a smooth fitness 5.45


You should find one in the free manual you can download at http://www.smoothfitness.com/support/product-manuals.htm

Nov 05, 2011 | Smoothfitness Smooth 5.45 Folding...

1 Answer

Wiring diagram need for an Smoothfitness EVO treadmill.


Solved this problem by contacting the Evo/Smooth directly. Great service.

Oct 19, 2009 | Treadmills

Not finding what you are looking for?
Smoothfitness Smooth 5.45 Folding Treadmill Logo

Related Topics:

573 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smoothfitness Treadmills Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

286 Answers

Jon Schniers

Level 1 Expert

13 Answers

Are you a Smoothfitness Treadmill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...