Question about Zanussi 29 in. LS14 Free-standing Dishwasher

2 Answers

Zanussi LS 14

Hallo! I have a problem with my Zanussi LS 14. I get the error C8. Can anybody help me? Thank you very much.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

For remove C8 error on zanussi LS14 you must press on/off and press cycle2 key and you get FAC press cycle2 key again 8 times and you get CFG enter on family of this paremeter pressing ifinity key go to parameter ALR and you get ALR= 1 change to ALR=0 AND FIX THE PROBLEM.

Posted on Jan 28, 2011

  • kev1974 Apr 18, 2011

    Didn't work, see below!

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1.Put machine in standby (no display) 2.press power

Posted on Apr 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

C8 SHOWING AND NOT WORKING.I have reconnected the burnt connection on main heating element. Unable to re-set.


C8 - During rinse phase boiler doesn't empty:

  • Rinse pump not efficient.
  • Rinse arms obstructed.
  • Boiler level sensor out of order.
Dado

Feb 03, 2016 | Zanussi Dishwashers

1 Answer

Replaced drain pump and control board in cabrio washer, still does not work


Go back to the shop and ask them to explain why the diagnostic routine stops at C8 and reads error F72. No doubt they will blame it all on something else but you could get headed for a cure.

Apr 16, 2014 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Trigonometry, my calculator says domain error when I press; cos-1(26^2+14^2-32^2/2*26*14) I change it into degree, but it doesn't help.. Can anybody tell me why it doesn't give me the exact an


Domain errror meaning that an argument must be in a specified domain.
It's not clearly what do you want to do but for three possible options solutions are on the captured images below(for radian mode).

2_23_2013_2_59_50_pm.jpg



2_23_2013_3_00_57_pm.jpg



2_23_2013_3_02_25_pm.jpg

Feb 23, 2013 | Texas Instruments TI-89 Calculator

1 Answer

ERROR CODE E 60 washing machine zanussi ZWG1100M


This can be due to error in the control board. Shut down and remove plug and when switched on press down the start/stop button. If the error does not clear this can be a fault in the motor drive within the control panel board.
Remove the panel and check the connections to the motor, check the motor and the capacitor to the motor or if the motor is jammed.

Jul 03, 2012 | Zanussi Washing Machines

1 Answer

Zanussi dishwasher LS9 AD/G1 reading code C8 and not working


C8 - During rinse phase boiler doesn't empty:

  • Rinse pump not efficient.
  • Rinse arms obstructed.
  • Boiler level sensor out of order.
Dado


Jun 25, 2012 | Zanussi 29 in. LS14 Free-standing...

1 Answer

Warning C 08 how to reset?


Hold down on/off and prog 2 for 5 sec.
display ``fac``
Press prog 2 until display ``ron``
Press prog 3 until ``c8 / 1 or c8/3.``
Press prog 1 until ``c8/0``
Press prog 3 until ``ron ``
switch off -switch on and o.k.
General
C8 caused from glogged jets or rinse pump problem or bad luck.
If there is a problem at the dishwasher then c8 will appear again

Hope I helped you

kostas

Jan 26, 2011 | Zanussi 24 in. LS6E Free-standing...

2 Answers

PALOMA PTG-74PVN-1 Code C8 12 my water heater


C8 is the last stop in the point of burner ignition and a total of eight error codes. Error code 12 is a supplemental code that means your LP gas supply is too low...have your LP tank service and try again.

HTH,

Mike...

Dec 06, 2009 | Rheem Paloma Tankless Water Heaters...

1 Answer

Help with zanussi it wont fill with water


you need to know the error, but could be low insulation heaters....you need to find error message which zanuzzi engineer will find

Jul 15, 2009 | Washing Machines

Not finding what you are looking for?
Zanussi 29 in. LS14 Free-standing Dishwasher Logo

Related Topics:

1,823 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Owen Barnes

Level 3 Expert

835 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...