Question about Car Amplifiers

1 Answer

How can i connect wifi in to my system for net connection?

How can i use wifi in my system? how can get a window in which i can enter the mac address of a system to which i wanna give the authority to use net connection through wifi facility?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Control panel,new network connection, it will ask for mac address and set it up if your trying to let some one else use your wifi they will have to connect to your network and enter your info upon connection

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error or disconnect from server why?


you have an unstable internet connection.
you need to repair or refresh the ip address of your network connection.
fix loosen ethernet and lan cable connections. make sure router and modem is not overheating too.

Feb 11, 2011 | Crossfire XP1000D Car Amp

1 Answer

How do i install it it was a hand me down with no instructions


http://dl.owneriq.net/a/a44b260d-f7bb-4ae7-bd9f-5a4722cb9427.pdf

in general

the positive terminal is connected to the positive of the battery

the negative terminal is connected to a metal grounding point on the car ( find a metal spot on the car to connect the negative terminal of amplifier)(do not connect it to the negative side of the battery)

the remote terminal connects to either the remote line from the back of the radio blue and white wire

if the radio does not have a remote wire then use the red wire which is the acc (check this against your car wiring)

the speakers are simple connect the positive of radio to positive terminal ect

and the input comes from the radio as a phono jack connect that to the input of the input of the amplifier right left ect ect also if the radio has only left and right then you need a splitter for the phono cable because your amp is 4 channel

if the radio does not have phono jacks then you need to take the output that usually goes to the speakers and route them to the amp and attach pho no jacks on them

Jan 10, 2010 | Alpine MRV-F357 Car Audio Amplifier

2 Answers

Lightning audio b150.2 as soon as +12 is hooked up blows 25 amp fuse and the c2 1000uf/35v capacitors blow???????


Disconnect all speaker connections and rca cables. Leave power, ground and remote wires intact. Try turning on again. If you still have a protection light your amp is faulty. Hopefully you have warranty. Double check all connections .A thumbs up would be greatly appreciated if this answer is helpful to you.

Aug 25, 2009 | Lightning Audio PC2 Capacitor Car Audio...

1 Answer

How do icoonect high input, especially the ground wire


Hello admiralebail,
Here is the link to DHD's web site: www.dhdusa.com. Their web site does not show a download page or even a support function. Not even an email address. They do list their snail mail address and phone number, though. My recommendation is to call and see if they will send you the manual.
Hope this helps.

Apr 20, 2009 | DHD NTX-2004 Car Audio Amplifier

1 Answer

Derivas


go to this address on the web and enter in product info and download drivers here:
http://esupport.sony.com/US/perl/select-system.pl?DIRECTOR=DRIVER
make sure after you mark this question as solved thanks

Jan 08, 2009 | Sony Xplod XM-554ZR Car Audio Amplifier

1 Answer

Externally fused amplifiers


I believe it's because the fuses (or any other connection point) is deemed to be a weakness. If an amplifier is properly installed, there will be a large fuse as close to the battery connection point as possible. Any other fuses in the amplifier itself would be considered redundant. From a safety standpoint, if an installer chooses not to fuse the main power wire to the amp the fuses in the amp will not prevent a fire from occuring should the wire get shorted. Therefore there MUST be proper fusing on the power wire and further fusing in the amp is not necessary.
The other reason for this may be that in many larger amplifiers from reputable companies (RF and others) they use un-regulated power supplies to get the maximum from their amps. Fuses could be considered a bottleneck in these systems as a properly installed system, again, has the required fusing at the battery.

Oct 03, 2008 | Rockford Fosgate T600-2 Car Audio...

1 Answer

Car hifi manuals


If you can't locate them, I could walk you through it.
It would take a complete description of your current system and what you hope to achieve, if anything.
High quality pics of all amp connections and controls followed by a phone call.
Having done several thousand installs, I have pretty much seen everything, but with 6 channels and internal x-overs it gets a little complicated, but definitely do-able. Let me know
Regards, Paul

May 15, 2008 | Car Amplifiers

1 Answer

No sound from speakers after mra-f350 connected to alpine w205


Did you set the digital output to the on position on the bottom of the head unit?

You have to switch the head unit off then back on for it to recognize the position of the switch.

Oct 27, 2007 | Alpine MRA-F350 Car Audio Amplifier

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...