Question about InFocus ScreenPlay 4805 Multimedia Projector

1 Answer

4805 Green lights comes on but immediately turns to red blinking light with no picture.

Posted by on

  • tirtha73 Mar 01, 2009

    I have same problem; green light comes then blinks with red light and no picture. Please guide me.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 167 Answers

In the manual there is a chart which will indicate the nature of the failure depending on the number of times the red led flashes before a pause.

Most common is the projector's lamp timer has exceeded the operational lamp time limit.

While the projector's red led is flashing, press the volume up and down buttons on the projector simultaneously and hold them both in for 10 seconds.
This will reset the lamp inhibit protocol.

However if the lamp has thousands of hours of use you need to replace it before it actually fails.

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Infocus Screenplay 4805 No Display, help?


hi friend,
please try to clean the testing diode of color wheeel.
Jack

Nov 22, 2011 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

InFocus ScreenPlay 4805 no projection. Unit powers on and green light blinks, but no light and no fan, eventually red light blinks continuously about 2 seconds between blinks. When the green light is...


the high-pitched sound is the colorwheel trying to spin up to speed. that may need to be replaced. check the inside of the lamp for bulges, black spots, fogging or flaking. if it has any of those, replace the lamp. you can get parts from an infocus service center or send it to them for repair. either way, try www.avsolutionsny.com they're really good. if you want to replace it yourself, there is a detailed step-by-step on my "tips" area. it's the same as the infocus x1, x2, x3 and sp4805. click on my picture and scroll down to tips. good luck!

Feb 01, 2010 | InFocus ScreenPlay 4805 Multimedia...

2 Answers

Projector screen turns off after 10-20 seconds


Is the projector receiving a source signal? if not it will power itself down after whatever time you have it set to do so when no signal is present.
Just an idea?

Jan 03, 2010 | NEC NP-1000 Projector

1 Answer

New lamp won't light


I am having the same problem now. I am currently trying to reset the timer...but have yet to successfully. But I do think this is the solution.

Jun 10, 2009 | Sharp DT-100 Multimedia Projector

2 Answers

Infocus 4805 Lamp will not ignite after new bulb and reset.


it there is no high-pitched squeal when it starts up, the colorwheel needs replacing. the lamp won't light without it. the part is under $50, but installation is quite involved.

Apr 16, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

I turn on the 4805,green led blinks & bulb does not come on?


After a few minuets does the green blinking light turn to a red blinking light?

If so the problem is the lamp did not strike.Either the lamp has failed (most likely) or there is a problem with the power supply (less likely)

Feb 12, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Infocus 4805 - Doesnot display and make noise at start-up


Well a single red blinking means the lamp won't strike after five (5) attempts. The "squeaking" sound if it's coming form the large fan usually always means the Mos-Fet fan speed controller chip has failed which presents sometimes as an intermittent squeaking sound. Which would implies the lamp may have failed from the resultant over temp. However if the squeaking noise is coming from the color wheel that would mean it's bearings have failed and if is is unable to phase lock at reference speed the lamp would also not strike. The odd symptom is the remote thing... That does not fit! If is actually is related to the common cause of all the problems... That leaves only the power supply has partially failed (not too expensive) causing all of these symptoms.

Or murphy has moved in...

Good luck!

SagerTronics

Oct 28, 2008 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Infocus 4805 blinking red light problem


My first questions is:

Is this the first lamp you have placed into your Infocus pj? If not, did you reset the hours when you did it last time? Otherwise that can also confuse the projectors internal system thinking there is NOT a new lamp in there and there for make it stop working once the clock hours are expired and over the 3000-6000 suggested hour life.

Let me know so I can help trouble shoot other possible problems.

Oct 27, 2008 | InFocus ScreenPlay 4805 Multimedia...

Not finding what you are looking for?
InFocus ScreenPlay 4805 Multimedia Projector Logo

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Multimedia Projectors Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you an InFocus Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...