Question about Invoca 326348 Remote Control

1 Answer

I have an invoca tv remote with voice and just want remote to wor

I hate this remote. I have lost the directions and now my tv is stuck on channels between 225 and 275. I cannot change the tv and the remote won't work. How can I program this remote to ust allow me to do this manually and not use the voice activation., Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 350 Answers

Click on the following lind for the manual....

http://www.remotecodelist.com/remotes/invocamanual.pdf

jackiaria

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remote control three U-Verse set top boxes that are side-by-side?


If the set top boxes are identical and use the same remote control, there is no way to change things

Feb 18, 2013 | Invoca Telemania 025448 Remote Control

1 Answer

Please can anyone help. My mother has very bad eye sight and I managed to get hold of a inVoca voice attivated remote control for the tv to try and Make things easier for her but it will not link in


Go directly to the manufacturer:
This product is available from:

Manufacturer:

Innotech Systems Inc.

320 Main Street
Port Jefferson, New York 11777
United States
Telephone: 631-473-1500.
Fax: 631-473-5259.
Web: http://www.innotechsystems.com.
Email: sales@innotechsystems.com.

Jan 04, 2013 | Remote Controls

1 Answer

I have a dynex tv I want to install the remote


Codes to check with Dynex brand TVs are: 0004 0009 0044 0135 0049 0051 0189 0053 0147 0039 0130 0227 0233 0250 0252 0254 0257 0265 0266 0310 0325 0456 0040 0041 0042 0021 0023 0024 0179 0045 0025 0027 0030 0032 0034 0035 0037
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand. If you wish to know more, check this.

Dec 31, 2012 | KNG America InVoca 3.0 Remote Control

2 Answers

I can not get the invoca remote to sync to my tv


If you can't find the code for your particular model, you can perform an auto search with your remote.

If you don't have the codes for an item you are trying to use your remote with, you can perform an auto search.



Manually Turn on the device you wish to program.

On the remote, press the device key for which you are searching.

Press "Prog" button once. (two flashes)

Make sure the remote is aimed directly at the device you want to control.

Press "Auto" button (one flash)

InVoca will now search through the library for the target device code in three second intervals. Every 3 seconds the remote will prompt you by flashing the light, and the remote will test the new code by attempting to turn the device power off.

The top line of the LCD display will show the device type and the second line will show the device code number as it searches.

When the targeted device turns off, immediately press "Prog" to save the device code in memory.

After you have pressed "Prog", check the other buttons, such as CH and VOL to be sure they work. If not, repeat the above steps. When the auto search is re-started, the search for the target device will begin where it stopped.

To stop the "Auto Search" press any key except "Auto"

Hope this works for you.

Jul 13, 2011 | Invoca 326348 Remote Control

1 Answer

I have a Vizio TV and just bought a InVoca 3 voice activated remote control. I did not see any manufacturers codes for my Vizio that I have to enter into my InVoca 3. Can I use my Invoca 3 with my...


For the InVoca 3.0 I used a Goldstar TV code for a Vizio TV.I'm not sure what the 3 digit code was but you can search Goldstar codes on theremote shown in the manual with a 2 digit code 33. You also can train it fromyou remote but I did not try that method. They might have different manualsbecause my manual has more instructions than the online version one.

Aug 17, 2010 | KNG America InVoca 3.0 Remote Control

1 Answer

Channels keep changing while watching TV !!!


You may have the volume on your invoca set too high and it is picking up speech from the television and misinterpreting it as commands. Check the mic level in your battery compartment and mess with the levels so that it still listens to you, but not the tv :)
You can find the manual here and check pages 53 and 58 for better views :) Let me know if this doesn't help. You may have to move the invoca unit itself to a new location that isn't in the "main blast" of the tv speakers. Best of luck mate! Cheers!

Jun 17, 2010 | KNG America InVoca 3.0 Remote Control

1 Answer

Need manual for invoca 3.0 remote can anyone help


just google invoca and go to the manuel
then just print it thats what I did for the one I bought for $0.85

Dec 28, 2008 | Invoca 326348 Remote Control

1 Answer

Lost remote programing directions


Great News!! We can program most Philips Universal Remotes with Automatic Code Searh. Here's how it works on most of our remotes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

The above assumes that you want to store the VCR you want under the VCR but, Cable codes under the CBL, etc

Note: if the device does not have a chat channel at a button, you should Play (VCR only) or Power instead.

Here is a Code List on PDF that shoud be universal for most remotes. It worked for me.
http://www.remotecodelist.com/remot...ps-Magnavox_PM525S.pdf

Hope this helps you out, good luck.

Nov 27, 2008 | Philips Magnavox Learning Universal Remote

Not finding what you are looking for?
Invoca 326348 Remote Control Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Invoca Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Tom Chichester

Level 3 Expert

24564 Answers

Are you an Invoca Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...