Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

E-10 My washer keeps flashing E-10 after running awhile, what does that mean?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Frigidaire Master
  • 8,147 Answers

Good question. I pesonally cannot answer this question but I know somebody who can answer this: Post your model number to any of these fine forums for
a simple answer that will save you lots of money:
http://appliancejunk.com/forums/index.php?referredby=858
http://forum.appliancepartspros.com/
http://applianceguru.com/

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The start button keeps blinking, WONT LET ME DO ANYTHING


Cycle light flashes, but machine wont start - Kenmore Elite ...

https://www.ifixit.com/.../Cycle+light+flashes,+but+machine+wont+...
iFixitIf this pin breaks off, the washer will not recognize that the door has be. ... Whatever cycle I choose, the light just flashes and holding the start button does nothing. ... I don't seem to have a black pin....the normal wash button just keeps flashing ...

GE Washer Start button flashing - DoItYourself.com Community Forums

www.doityourself.com/.../386041-ge-washer-start-button-flashing.html
Apr 6, 2009 - GE Washer Start Button flashing will not start Model WPRB8050D1WW, tried holding start button in for 5-10 seconds, did the unplug for 30 ...

Oct 29, 2015 | Washing Machines

4 Answers

F11 code flashing-washer stops


hi!!!!

try to unplug it end then check the control timer if it is broken !!!!

or open it if you know and fix it may be the spring that pull back the pause botton
might be broken go check it?

Sep 19, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Drum not spinning, seems to be stuck


LE error means "Motor Error" that your machine's motor is faulty and needs to be replaced.

Dec 22, 2013 | LG WM-1832C Front Load Washer

1 Answer

When water goes into tub suds flashes for awhile then f35code


Hello & Welcome to FixYa

F35 error means that there is some sort of issue with the steamer electronic board and analog pressure sensor has gone bad.
To solve this problem you have to take the bottom front panel apart and then clean the drain filter pump assembly completely, make sure the washer is unplugged before working on it. Check that the hose is firmly attached with the washer and is not blocked. You can also check the water level pressure switch operation. Please get back to me if you have any other questions.


Kevin

Jun 14, 2011 | Kenmore HE3T Washer

2 Answers

My Washer starts then beeps continuously and flashes F 50??? Can anyone tell me what this means?


F then 50 flashes when the motor rotor position sensor (RPS)
senses no rotation.
Does basket turn freely? If not, determine cause of friction.
If basket turns freely, see TEST #3, Page 10.

Mar 25, 2010 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Code lf keeps popping up


lf code means long fill. If the water fill time exceeds 10 minutes, the water valves are turned off and lf is flashed. Press STOP/CANCEL to clear the display.

Mar 24, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Base moves too much and only spins for awhile before dispaly ul


The washer needs to have the auto leveling legs reset.

The message you're getting "ul" means "unbalanced load" and usually results when washing lots of towels or lots of jeans, etc., basically large fabric that holds quite a bit of water.

In order to get the washer leveled, you will need to stand at the front of it and reach to the back sides and tilt the washer towards you, keeping the front of the washer on the floor and tilting/lifting the rear of the washer about 4-5 inches off the floor. Once you've got it up, just let go of the washer and it will hit the floor and self level the rear legs.

You can then use the adustable front feet to get the washer stabilized so it doesn't more all around when doing laundry. Try not to lift the washer much when adjusting the two front corner feet. The goal is get the washer stable and solidly planted on the floor so it doesn't move around when running.

Hope this was very helpful and best regards!


Aug 07, 2009 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Kenmore Elite HE 5t


Low or no water supply, hot or cold side or water pressure switch not switching over to indicate fully filled though if this happens drain motor will continue to run continuously while f-20 flashes

Jan 15, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...