Question about Hobart 24 in. LXIC-5 Built-in Dishwasher

1 Answer

Dishwasher will not fill .... HOBART

The water intake solenoid are ok(i bypass machine signal and water went in ) will not rinse also

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

Please post a model number.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Find out why hobart bar aid hood dishwasher not rinsing


A model number would be handy...
Take it the thing fills OK (possibly a bit slowly?)

Unboosted machine look at water pressure/flow (clogged strainer; shared supply; scaled boiler outlet);
Boosted machine look at booster pump (motor dead; impeller broken; capacitor failed)

Feb 16, 2015 | Hobart Dishwashers

1 Answer

Dish machine sticks in rinse cycle


Check the solenoid valve on the rinse piping at the top back of the machine. shut water off and take the coil and the top off of the solenoid, carefully remove the innards (so as not to lose them and to remember how they went together) check for debris inside and clean out. Put it back together and try it. If that doesn't work, you will need to replace the solenoid valve. Cost is around $100 at Grainger for a suitable valve or if you want factory part, it is around $350 from Hobart.

Oct 28, 2013 | Hobart Dishwasher Am-14 Commercial Dish...

1 Answer

Water spraying continue sly from the bottom arm, even when the power is off?? What can be the problem?


I assume you mean the (smaller) rinse arm? You most likely have debris inside your water fill solenoid valve. Turn off water supply and disassemble valve carefully to avoid losing parts and clean out valve, you can also crack water supply to flush it out briefly while solenoid is apart. reassemble in same order that it came apart and try it again. If that doesn't fix it you need to replace solenoid valve. $100 at Graingers or $350 from Hobart.

Mar 11, 2013 | Hobart AM14-253 Free-standing Dishwasher

1 Answer

Water wont come in the dishwasher. It is heating with out water and then smells like plastic burning. Hobart LX30


Check that your supply faucet is open, Check if there is a screen in the supply line, these can become blocked due to scale deposits from the mains. If there is no screen check that the inlet solenoid valve has not got blocked. If none of the above help, check that there is power getting to the solenoid valve when the machine is supposed to be on the fill cycle. If no power is getting to the valve, the timer might be faulty. (You can try hand filling the machine and see if it goes through a cycle, at least up to the rinse stage, this will tell you if the timer control is working).

Apr 18, 2011 | Hobart Dishwashers

1 Answer

Hobart WM-ID dishwasher doesn't heat water enough to clean dishes


The WM-1D does not have any internal heating devices. You have to supply the machine with the proper water temp. It has two fill valves, one for wash and one for rinse. It should have 150F supplied to the wash fill valve and 180F to the rinse fill valve.

Feb 04, 2010 | Hobart AM14C-155 Dishwasher

1 Answer

Hobart SR24H dishwasher will not spray, arm does not rotate


ck. flow press. of water , when fill solenoid opens press. should be @20 p.s.i because this is a time fill machine. this is important .not static press. flow press. also ck the screened washers in the fill hose to see if they are plugged .let me know what you find so i can futher assist. dont forget to vote tks

Jan 10, 2010 | Hobart 24 in. LXIH-3 Built-in Dishwasher

3 Answers

Hobart am14 water runs through it all the time


If water is running even with the machine turned off then your solenoid valve needs to be cleaned out or rebuilt. This valve is in the back top of the machine by the gauge.

Apr 24, 2009 | Hobart 42 in. AM14C-154 Free-standing...

2 Answers

Hobart LXiH preesure gauge is to low - 7 PSI


Todd - A pressure regulator will REDUCE pressure only. There is no back pressure - the machine's gauge is reading the incoming water pressure as it fills/rinses. Assuming the gauge is OK, the machine is only seeing 7 psi. There is an inline strainer in teh machine, check that for blockage. You said the machine was operating on 45 psi with a reading of only 12 psi. There may be some kind of pressure reducer - I have seen Hobart use special supply hoses with builtin orifices.

hope this helps, if not email me, i service commercial machines and came across your question as I was looking for help myself!

recordhound@yahoo.com

dishwasher in subject line

Oct 18, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Hobart lx30 : rinse cycle


The rinse water in a LX30 is driven by water pressure. A solenoid valve, bottom front - gold body, opens up and allows the water to flow.

If you are referring to the rinse agent pump, there must be NO leaks in the tubing or the hose that runs through the pump. And if the unit has lost its prime, using your hand to "seal" it, and forcing water from the faucet into the line can prime it.

Good luck - Mike

May 13, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

Not finding what you are looking for?
Hobart 24 in. LXIC-5 Built-in Dishwasher Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Ricardo311

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

handygirl911
handygirl911

Level 2 Expert

55 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...