Question about Zenith E44W46LCD 44" Rear Projection HDTV-Ready Television

1 Answer

How do you change projector bulb - Zenith E44W46LCD 44" Rear Projection HDTV-Ready Television

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 280 Answers

Remove the door on the side of the tv with a phillips screw driver. inside you will see a box with 2 screws . loosen the screws and pull out on the box using the handel in the center. When replacing the lamp and cage make sure not put your fingers on the lamp and wipe in off before you reinstall it. snug (not tighten ) the screws on the cage and replace the door. Make sure the door in closed properly. ther is a switch, and if the door is not closed all the way the set will not come on. Last make sure to clean all dust from fan vent and door area.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What should i do when my projector's temperature light is flashing red 30 sec after start up?

try changing the light bulb. they have a time limit on them. with mine, I had to change the light bulb. Not cheap, but it worked for me.

Nov 12, 2014 | Epson PowerLite Home Cinema 8350 3LCD...

1 Answer

Tv made pop sound no picture still sound

Your bulb burnt out. You can buy a replacement at

Nov 21, 2013 | Toshiba Projection Televisions

1 Answer

Cant change the light bulb

Consult the owner manual or Google the model number to locate one which will have instructions for replacement of the bulb.

Nov 02, 2012 | Sharper Image Entertainment Projector...

1 Answer

The picture went blank on my tv but I can still hear the sound. How can I get the picture to come back? All plug ins are tight. Thanks

When was the last time you changed the bulb for the projector? has this gone bad? If the bulb needs changed, consult your manual for instructions and if the bulb is good let us know.

Mar 24, 2011 | RCA HDLP50W151 50" Rear Projection HDTV

1 Answer

Have a KDF 60Wf 655 will not turn on. Green light comes on then red light with 7 blinks any suggestions? Took bulb out but the bulb light never lit and the bulb doesn't look blown.

Wether it looks blown or not replace it and dont put oil from your fingers on the bulb. Also clean the cooling fans for the bulb and projector (which may mean taking the back off and taking apart projector). Dirt in the projector fans can cause a fault not allowing for the unit to turn on. All the cooling work ins conjunction with a good bulb.

Apr 24, 2010 | Sony Grand WEGA KDF-42WE655 42" Rear...

3 Answers

How do I open the top of the projector to replace the light bulb?

Hi, Follow :- There is a Video as well on the same page.If you wish to Purchase the Bulb, you could consider :- Let me know, if needed further assistance, Hope i helped you. Thanks for using ' Fixya ' and have a nice day!!

Feb 10, 2010 | Projection Televisions

1 Answer

I have had my projector for abourt 2 years and the projector indicated that the bulb life was almost up and had to be replaced. I bought the new bulb and installed it with no problem. when I turned on...

Please ADD the make and model of your projector on the comment page.

Without the model information,I can only give you few location to check on.

Check for an air filter or air clear.

Some unit has the smart to sense for filter change. In general you must do both at the same time.
(once again this is general info. Without the model #,I only can tell you to look for the filter)

The next item is check for safety switch/latch for open. The project has built-in safety.
Make sure all door/latch are close securely.

Do a quick cleaning and check for loose parts.

Please ADD the model number under comment page.

I will follow up later.

Jul 23, 2009 | Projection Televisions

1 Answer

Projector tv the red and green colors are not in sync

no its a convergence tube problem u shud change the green tube.

its the exausted one in this case.

Mar 15, 2009 | Philips 60PP9202 60" Rear Projection...

1 Answer


look at your users manual.
all epson models need to have lamp life reset befor the lamp will light.

I have had this same problem befor.


Jan 11, 2009 | Projection Televisions

2 Answers

Projector bulb issue

it takes longer for screen to start. picture becomes dull. screen will sometimes flash a little.

Jan 02, 2009 | Sony Grand WEGA KDF-60WF655 60" Rear...

Not finding what you are looking for?
Zenith E44W46LCD 44" Rear Projection HDTV-Ready Television Logo

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers


Level 3 Expert

61249 Answers

Are you a Zenith Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides