Question about Home Theater Systems

1 Answer

When i turn on the tv on the power butten clicks on and off three times. then it takes about 45 sec. before i can try agian

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Please check the speaker wire connections, the system may be detecting a crossed or shorted speaker wire and will not play.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clicking noise on Multitech/Dolby setting


Hi,

Did you experience this from the start (since the first time you used it) or did it started just recently? Check that the HDMI cable is connected properly at both ends and it's not near/touching any other cable or power supply. After checking this and if it is still there then it could be a fault with the cable. If you have another cable to try, that would be great.

Dec 26, 2007 | Philips HTS-6500/37 System

2 Answers

Insignia akb36157101 does not power the tv any


Aim remote at the TV, hold down the TV Power button, and press the CH up button until the TV turns on/off. This cycles through 45 manufacturer codes.

Mar 13, 2010 | Insignia Digital-to-Analog Converter for...

2 Answers

Have a converter box. Had to change battery in remote and now tv will not turn off.Have a rca tv


hold the power on off button down and press the channel up button repeatedly up to 45 times until the tv set turns off.

Dec 11, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

I cannot turn off the TV,with the insignia remote control


Read the first time start up instructions .. This is what worked for me.

Hold the power-on/off button down while simultaneously pressing channel up , repeatedly for up to 45 times. when the TV shuts off stop, release the on off button.

you should be able to turn it on and off, if you went too far (pressed up arrow too many times), go the other way (holding down the on off and pressing channed down) until it turns on again.

Nov 30, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

No vaild cd when theres a cd in the dvd player


I'd be guessing the problem being just dirt and grime over the years. The open and close problem would be due to dirt and dust on the sensors that tell it wether the CD tray is open or closed and where it is whitin its tracks. You need to find them and clean them all with contact cleaner or rubbing alcohol, but to do so, first you need to take the whole thing apart to get to the CD reader part. So if you don't feel safe enough taking it all apart yourself, take it to your local technician and he'll do it. As for it not reading the CD/DVDs, that's also due to dirt and dust but on the optic lens of the reader this times though. You just need to clean it with a cue-tip and some windex or any good glass cleaner. Be careful when cleaning the little lens in the reader head though, cause it is very fragile, and also make sure to not turn it back on if there was some cleaner that got in the head itself. If you can't wipe it off carefully, just let it dry there for a few minutes or so and then turn it back on. Again if you don't feel safe enough taking all this apart, take it to the local tech and he will gladly do it for you.

Jul 07, 2009 | Durabrand STS92 System

1 Answer

Tv will not come on.


your tv remote sensor is gone,you gonna have to take it back to where it was purchased from,let them repair it under warranty

Jul 03, 2009 | RCA RTD 130 System

1 Answer

How do I program my tv set to operate from the Insignia remote controler


on the remote battery cover there should be instructions... mines was this but i dunno for u:

hold powerr for 3 seconds
hold TV for 5 secs
keep pressing power until tv turns on

Jun 30, 2009 | Insignia Digital-to-Analog Converter for...

4 Answers

Remote Control


From GUEST: I found this solution in the manual and will perform this task again to see if I can get the tv will be re-recognized again. Give this a try, too.


Remote will not turn on or shut off the TV.
• You must program the converter box remote in order to control your TV power button.
• To program the remote control:
    1. Determine if the TV is a model that can be controlled by the remote control. See "Controllable TV brands" on page 17 in the manual.
    2. Turn on the TV.
    3. While you press and hold TV POWER on the remote control, press CH ^ or CH v one or more times until the TV turns off. Each time you press one of these buttons, the remote control sends a manufacturer code (between 1 and 45) to the TV.

Sep 01, 2008 | Insignia Digital-to-Analog Converter for...

2 Answers

Media center not working


hi
can you please help me.How can I solve this problem.
The Media Center system doesn't work and the AdaptiQ CD (2) is in the Media Center. We can't put out the CD.

Dec 22, 2007 | Bose Lifestyle 38 System

Not finding what you are looking for?
Home Theater Systems Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Theater Systems Experts

Gyula Lacz

Level 3 Expert

482 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

kakima

Level 3 Expert

96396 Answers

Are you a Home Theater System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...