Question about Zebra Z6M Plus Thermal Label Printer

3 Answers

Printing error condition

Zebra printer Z6M error condition paper out our error condition head open, i am change the ribbon and tage but problem not solve

Posted by on

  • anilku_singh Feb 27, 2009

    2 nos. zebra z6m label thermal printer, prblem is error condition paper out our error condition head open, a am change

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 155 Answers

First clean the sensor tag and sensor head open and tape. Then perform a calibration label pressing the PAUSE and FEED buttons and turn on the printer, release the keys until it starts to move the label. Wait until you are finished and ready to print.

Posted on Mar 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Solution from Noel O'Kell fixed my issue. the two sensors below (ribbon and printhead)it should be clean, dont touch them, spray them with canned air. Also these couple of sensors should be as close as possible and in the best angle to be able to sense the reflection from the chromed metal piece sitting above them when the head is closed.

Posted on Jun 28, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Minha impressora esta no panel impreesao.aguard. e que isto
a nao imprime na porta paralela

Posted on Jul 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Error print head open on Zebra 6m plus. Load ribbon and stock close head and it will start to calibrate then the error print head open comes up. 2 new sensors have been installed by a Peak tech. Is there...


The sensor on this printer is a double sensor. The side close to the frame is the head open and the one on the outside is the ribbon present. It is adjustable. They both reflect off the chrome surface of the head assy. above them. First clean the chrome surface above the sensor and test before adjusting. There is one screw that you can loose and tilt the sensor to match the angle of the chrome plate above. Also the gap between the sensor and the chrome surface is .060in. or 1.5mm.

Oct 19, 2010 | Zebra Z6M Plus Thermal Label Printer

1 Answer

I have one z6m and the error is: Printhead open.but the printhead is closed. Please help me. Thank you.


push down the print head assembli and you will see what the probles is then ajust it.

Jul 07, 2010 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Zebra Z4 Error message


ribbon in means, you choose direct thermal print method which is printing without a ribbon and yet you print with thermal transfer print method.

just check on lcd panel , change the print method to thermal transfer. and make sure the setting on your driver is thermal transfer too, or else it will keep reverting back to direct thermal

Feb 04, 2010 | Zebra Z6M Plus Thermal Label Printer

2 Answers

Have X3 Zebra 140Xilll printers. These printers will stop printing with a message "Error condition Paper out". But the paper is loaded. Everything seems fine. What can I do? Thanks Steve Rolland


Check and clean the sensors, also the reflective surface. Make sure there are no lables stuck to the reflective surface. Use Isopropyl Alcohol to clean.

Jan 21, 2010 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

I have a zebra z6mplus the ribbon keeps breaking


You may have your contrast set too high. If it breaks as it feeds under the printhead (while printing) your contrast may be set too high.
You also could have a ribbon spindle issue. Are both ribbon spindles turning?

Jul 08, 2009 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Z4m zebra printer problem


Might foul the ribbon sensor, clean the sensor and try to print again.

Mar 02, 2009 | Zebra Z6M Plus Thermal Label Printer

3 Answers

ZM400 printer


Try going through the LCD menu and if it say "Direct Thermal" change it to "Thermal Transfer", Direct Thermal made means, no ribbon required, but it sounds like you do have ribbon in the printer, if so, try my recommendation. If it asks for a password, it's '1234'.

Oct 14, 2008 | Zebra 203DPI Printer

1 Answer

Error conditon ribbon out


if you are not using a ribbon you should configure your printer properties in direct thermal the same with your printer configuration in LCD Panel, if your printer properties is different with the LCD Panel error condition ribbon out will come out to your LCD Panel

Jul 27, 2008 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Z6M printing issue


try adjusting the presure of the printhead

here is the site for the manual

http://www.zebra.com/id/zebra/na/en/index/resource_library/manuals.results.html


good luck

Dec 12, 2007 | Zebra Z Series Z6M Thermal Label Printer

Not finding what you are looking for?
Zebra Z6M Plus Thermal Label Printer Logo

2,816 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Printers & Copiers Experts

pkwc

Level 2 Expert

254 Answers

lancer284

Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers

Are you a Zebra Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...