Question about Whirlpool LSR5132PQ Top Load Washer

1 Answer



Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 686 Answers

Timer and motor, timer cost about 68USD and motor 130USD you need a qualified repair person to look at it

Posted on Apr 06, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

With flashing light f 12

F12s low water pressure, normally either te taps stuck or the fill hose is kinked/blocked

Dec 27, 2014 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Hello, after the first fill it will trip the circut, I have tried what I believe to be a different circut with the same result. Washer still full of water, please help.. Thank you for any help. Model# ...

Check to see if this may be caused by a Ground Fault Interrupter. If water has gotten into the electrical system of the machine, this will continue to trip until the fault location has dried out and no longer causing electrical leakage. If this is a standard breaker that is tripping, this would mean you have a shorted motor causing it to draw excessive current.
The combination breaker/GFI can itself fail; I replaced several of these after only a few years of service.

Aug 08, 2011 | Whirlpool Washing Machines

1 Answer


if the spin speed is slow it could be the clutch is worn out.

Mar 21, 2010 | Whirlpool LSQ8000 Top Load Washer

1 Answer

It is not draining completely or spinning

My Whirlpool Duet wisher will come on; but will not spinning at all! But sounds like it is working.What can I do to fix it halp halp!!

Dec 14, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool LSR5132PQO not working

and also the "drive motor to transmission coupling" is probably broken. You need a repair person.

Feb 27, 2009 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

Whirlpool LSR5132PQO not working

Check the lid switch with a volt/ohm meter for continuity.
If no continuity, replace the lid switch.

Check the direct drive coupling on the motor.
If it will not drain, bad lid switch.
If it will not agitate or spin bad drive coupling.

Feb 27, 2009 | Whirlpool LSQ8000 Top Load Washer

1 Answer

Kenmore elite lock problen

I had the same problem. Turned out, electronic panel behind the door had spring action malfunctioned because of misplaced spring, which in turn caused panel to not generate a signal which, stopped the whole cycle.
Here is what I did to fix the problem- 1. Open the door 2. Remove the ring behind rubber-cover on the door. 3. Reach out to the inside-right of the door. 4. Remove the panel after removing electric connections. 5. Fix the spring action. 6. Put everything back and start the machine over.

Dec 31, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

LSR5132PQO Whirlpool Washer (Top Loader)

John, it's possible that it could be the basket drive. It sounds more like the clutch assy. Take the agitator off and look at the drive block. The two ears from the basket drive should be tight into the drive block, I will attach a picture of how it should look. If that looks ok, then I would suspect the clutch. They are not hard jobs, either one of them. 96d31f5.jpg

Aug 17, 2008 | Whirlpool LSQ8000 Top Load Washer

1 Answer

Washer wont go through spin cycle

Bent pinched or clooged drain hose. Other cause may be the drain filter in the front of the machine. (The small door on the lower left of the machine) With a pan, remove the cap and drain water from the small tube. Then open the larger cap and clean out the lint. This should solve the problem.

Dec 17, 2007 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

Not finding what you are looking for?
Whirlpool LSR5132PQ Top Load Washer Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides