Question about JBL Eon15P-1 Main / Stereo Speaker

2 Answers

Dead JBL EON 15P-1

Fuse blows again when replaced. torroidal xtfmr. seems ok. measures 60VAC when disconnected from amp. board. speakers seem ok too. each measure approx. 4 OHMS. Any suggestions on troubleshooting the amp board?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did you measure 60vac across total secondary or 60vac from center tap?

Posted on Dec 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

Bad power board. short on board

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a jbl 515 eon no power every thing is dead the fuse is ok


If you can watch the fuse kind of twitch. Most likely you have somthing shorted in your output amps. ( the ones on the heatsink underneath PCB) you'll probolly need a tech for this one to change out the transistors. Still under warranty?

Aug 26, 2011 | JBL EON 515 Speaker System

1 Answer

I installed a brand new tweeter in my JBL EON 15 G2 & the new tweeter blew. What else could be the problem?


These are "powered" speakers and any little bit
of distortion can be amplified enough to "blow" it!
Also the amp could be "shorted"! Have your JBL
dealer test it!!!

Apr 20, 2010 | JBL EON 15-G2 Powered DJ Speaker With EQ...

4 Answers

Damaged JBL Eon15 Tweeter


you can probably by a generic type of motherboard from a shop like JAYCAR lookem up on the net ]

May 25, 2009 | JBL EON 15-G2 Powered DJ Speaker With EQ...

1 Answer

Jbl eon


the eon woofer is designed to fit the small frame of the inside cabinet. The EV woofers look too deep to fit but you can try. I do think that the built in amps were set to work with only the JBL woofers so there might be a signal problem using the built in amp. The eon face seems to have their own screws to hold the grill so if they aren't holding you can drop some cement to help hold the srews in place. The front does not allow removal of the woofer so it seems whatever you do should not effect anything.

Nov 02, 2008 | JBL EON 15-G2 Powered DJ Speaker With EQ...

2 Answers

JBL Eon 15 Blown Fuse


These fuses are most likely 3 Amp fuses. Please note that if the replacements blow as well, that there is a problem within the amp section that will require repair.

Dan

Aug 14, 2008 | JBL EON 15-G2 Powered DJ Speaker With EQ...

Not finding what you are looking for?
JBL Eon15P-1 Main / Stereo Speaker Logo

Related Topics:

1,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top JBL Speakers & Subwoofers Experts

Michael Edwards
Michael Edwards

Level 1 Expert

53 Answers

 Grubhead
Grubhead

Level 3 Expert

4584 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a JBL Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...