Question about Zanussi WJS1265W Front Load Washer/Dryer

4 Answers

E10 code on a zanussi jet system washer

Washer starts cycle then after a couple of minutes stops with a E10 error does anyone know what e10 means. thanks

Posted by on

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 25 Answers

Is it a washer-dryer? E10 relates to a fault with the inlet valve.....usually the valve itself going open circuit.

Posted on Feb 28, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

E10 on Zanussi W/D
I had E10 on Zanussi W/D.
The machine would wash but not dry.
Changed the water inlet valve assembly.
All working again.
All credit to wildwest1959, thanks.

Posted on Apr 24, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Check to see if the water inlet is blocked.

the link below takes you to the manual, go to page 22

http://www.serviceforce.co.uk/pdfs/U21039.pdf

hope this helps

Posted on Apr 16, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is simply that water is not getting into the machine at a "reasonable" speed. Or NO water is getting in. It can be as simple as the water turned off at the place you connect your washing machine.

Posted on Sep 04, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My washing machine keeps stopping during its washing cycle and says fault E10


Thank you for your inquiry, Barbara Constable!
I see that your Electrolux washer is displaying an "E10" error code. "E10" stands for fill time too long you may want to check the hoses to make sure they are not restricted or kinked this could cause slow fill within your washer. If the hoses look to be in good shape then I would suggest it could be a faulty sensor or control panel. You could additionally reset your washer by disconnecting power from it for ten minutes. If you restore power and it continues to flash "E10" I would recommend having a professional out to properly diagnosis your washer. Hopefully this information is helpful. -Matt

Dec 21, 2014 | Electrolux Washing Machines

1 Answer

Error E10 keeps popping up and washer stops 2 or 3 times during cycle and have to reset it


E10 means that your cold water is coming in too slow, disconnect the cold water hose and check to see if the screen on your washing machine is clogged. If the screen is clean and the hose has good pressure then you will need to replace the water valve on your machine--- this is the piece that the hoses directly connect to.

Here could find additioan sample guide details: fixed-frigidaire-affinity-washer-gives-e10-error

Hope helps.

May 03, 2011 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Kenmore front load washer error code E 10 - washer stops and beeps periodically and needs to have start button pushed again to complete cycle. Seems to happen one minute into cycle and then a coupleof...


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 11, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

The washer gives an E10 error command at about 27 minutes left in the cycle almost every time


Check to make sure that your drain hose was not pushed too far down your drain pipe, you should have a loop where it goes in.

The loop will look like this:
http://www.applianceaid.com/newpics/leakdrainhose.JPG

Also, cause of the error could be that no cold water was getting through the cold water valve (inside the machine). Ends up usually being a loose wire to the valve

error code of E10 which according to my paperwork means there is an issue with the water supply

Nov 23, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

I can't change the default wash cycle without it switching


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.
2 Beeps/E20--Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.
3 Beeps/E30--Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.
4 Beeps/E40--Error: Door is open. Cause: Washer will not operate if door is open. Close door.
5 Beeps/E50--Error: Motor is overheated. Cause: Wait 30 minutes to cool down. Restart.
7 Beeps/E70--Error: Cold water doesn't enter. Cause: Hoses crossed,faucet problem.
15 Beeps/EF0--Error: Oversudsing. Cause: Too much detergent,or improper detergent for machine.
15 Beeps/EF0--Error: Hot water doesn't enter. Cause: Hoses crossed,faucet problem.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 28, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

I have a Frigidaire Gallery front load washer with E10 error code


When ours does that it is because of the hard water build up. We have to un-hook the hot water clean out the minerals and it stops doing it.

Jan 10, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Kenmore elite washer cycle signal keeps going off an on turing cy


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.
2 Beeps/E20--Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.
3 Beeps/E30--Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.
4 Beeps/E40--Error: Door is open. Cause: Washer will not operate if door is open. Close door.
5 Beeps/E50--Error: Motor is overheated. Cause: Wait 30 minutes to cool down. Restart.
7 Beeps/E70--Error: Cold water doesn't enter. Cause: Hoses crossed,faucet problem.
15 Beeps/EF0--Error: Oversudsing. Cause: Too much detergent,or improper detergent for machine.
15 Beeps/EF0--Error: Hot water doesn't enter. Cause: Hoses crossed,faucet problem.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 04, 2009 | Kenmore Washing Machines

2 Answers

Error code E10 on the electrolux ecovalve EWF1087 front load washer. What does this mean?


E10 is a timeout code. I found the answer on google by refining my search criteria. The tap was not turned on enough for the washer to fill up in time before the timeout was reached. After restarting the washer and turning the tap on further, the washer cycle completed without error.

Jul 22, 2008 | Electrolux Washing Machines

2 Answers

E10 error code


I had this problem, the washer/dryer stopped working while in the drying cycle and displayed e10 message. It was caused by a faulty three-way inlet valve. The solenoid controlling flow to dryer condenser proved to be open circuit. Pulled washer out from under counter top, unplugged, removed top cover, tested solenoid circuits with ohm meter and found one solenoid was faulty. The filter going into the unit was clear. Replaced whole three way component with one ordered on Internet and all now works fine. Noticed that during drying cycle, water to condenser is constantly being switched on and off, explaining why the green condenser solenoid is the one that wears out first.

Mar 03, 2007 | Zanussi WJS1265W Front Load Washer/Dryer

Not finding what you are looking for?
Zanussi WJS1265W Front Load Washer/Dryer Logo

6,702 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...