Question about E-Machines eMachines Desktop PC

1 Answer

My E machines 5260 won't start up! It appears to

My E machines 5260 won't start up! It appears to start then comes up with no video input! It used to be OK if left for a few hours but recently it won't start at all, just the "No video input" on screen. Any ideas? The PC is approx 5 years old.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

Techguru2009: You might have a static electricity charge on your motherboard. First you need to ground yourself before you open the case. Remove the memory cards from the motherboard. Turn your computer on without the memory installed, you should hear several beeps. The system is letting you know that you have no memory. Turn computer off reinstall the memory cards, close case and boot up. You might also want to reset the bios while you are at it, you can do this by removing the cmos battery for ten minutes. Warning: do not open the case while the plug is still on. Safety first. I hope this helps.

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

5260 looking for restore disc


Are you looking for a windows restore disc? Or a restore disc for the entire system which includes drivers for devices that came in the PC?

Oct 15, 2013 | E-Machines eMachines Desktop PC

1 Answer

My e machines home computer won't come out of.


Power save mode is just the message a monitor will display when there is no video signal from the computer to the monitor.

If the computer has no lights the problem is most likely the power supply and it will need to be replaced. Pretty easy to do, youtube it for tons of videos.

It also could be the motherboard is bad. I would start with the power supply first.

Dec 02, 2012 | PC Desktops

1 Answer

Can't install wireless network adaptor on emachines 5260. I used to connect to the internet using the wireless adaptor until I re-installed the windows xp operating system due to other problems, and...


Your machine was difficult to track down. As far as I can tell, the 5260 is the Intel motherboard. Below is a link to a page where you can individually download the drivers you require. Best of luck!
Greg

Intel 5260 Windows XP drivers

Nov 02, 2011 | E-Machines eMachines Desktop PC

1 Answer

When I turn on computer, the blue light comes on and the computer makes sounds as if it is starting and the monitor light is yellow. If I turn the monitor off and then back on, the screen says something...


No input usually indicates the machine is having trouble getting a video signal from the monitor. Check and make sure the monitor cable is connected properly. If you have another monitor also test the machine with another monitor.

Feb 26, 2010 | E-Machines eMachines Desktop PC

1 Answer

Monitor won't stay on. Error message comes up that says "no input signal", then monitor goes out.


Problem with the monitor, monitor cable, or video output. For monitor, if you have more than one input, make sure it's set to the correct one. Try a different cable. Try a different monitor. Check your video card settings--if you see the BIOS bootup screen while it's coming up then the Windows splash screen, then monitor blanks out, it's a Windows display setting. Boot into safe mode, then change settings--
  • Turn the computer on or Restart the computer
  • Start tapping the F8 key. The Windows Advanced Boot Options Menu appears. If you begin tapping the F8 key too soon, some computers display a "keyboard error" message. To resolve this, restart the computer and try again.
  • Ensure that the Safe mode option is selected (the top option)
  • Press Enter. The computer then begins to start in Safe mode.
  • When you are finished with troubleshooting, close all programs and restart the computer as you normally would.

Oct 31, 2008 | HP PC Desktops

1 Answer

Emachines 5260


yes you can download the audio drivers from the internet just type the machine brand name and model no. and select the os that you have

Apr 09, 2008 | E-Machines eMachines Desktop PC

1 Answer

USB 2.0 Host Controller on Windows 2000 Server (Emachine 5260)


raycrean, Windows 2000 service pack includes drivers for USB 2.0.
http://support.microsoft.com/kb/819332


How do you know its not operating like 2.0?

Jan 19, 2008 | E-Machines eMachines Desktop PC

1 Answer

Re: emachines model 5260


go to te control panel and click add hardware try reinstalling it!

Dec 09, 2007 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an E-Machines PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...