Question about HP PSC 1410 All-In-One InkJet Printer

1 Answer

Test page printing at the time of printer powered on

When the printer is powered on that times a test page is prined.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer


test page printing at the time of printer powered  - s.gif Solution minimtop.gif The product aligns the print cartridges every time that print cartridges are installed or replaced to ensure the highest-quality prints. The alignment page will continue to print every time that the product is turned on or off until the alignment process is completed. NOTE: If you remove and install the same print cartridge, the unit will NOT align the print cartridges. The unit remembers the alignment values for that print cartridge, so you do not need to realign the print cartridges. Follow the steps below, in the order presented, to correcttest page printing at the time of printer powered - s.gifmplete a print cartridge alignment. s.gif Step one: Remove the print cartridges minimtop.gif

  1. If the On/Resume buttontest page printing at the time of printer powered - c00316907.gifpress the On/Resume button to turn the product on. Figure 1: Press the On/Resume button to turn the product on c00316907.gif
  2. Make suretest page printing at the time of printer powered - c00316908.gifay is down and there is letter or A4 unused plain white paper loaded in the paper tray.
  3. Lower the access door until it stops. c00316908.gif Make sure the print carriage moves to the center. Figure 3: Print carriage in the center of thetest page printing at the time of printer powered - c00316910.gifc00316909.gif
  4. Wait until the print carriage is idle and silent, and then, using your thumb, lightly press down on a print cartridge to release it. Figure 4: The print carriage c00316test page printing at the time of printer powered  - c00316912.gifs=
    • If replacing the tri-color print cartridge, remove the print cartridge from the slot on the left.
    • If replacing the test page printing at the time of printer powered - s.gif print cartridge, remove the print cartridge from the slot on the right.
    Figure 5: The print cartridges in the proper position c00316912.gif test page printing at the time of printer powered - minimtop.gifolor print cartridge
    2 - Black print cartridge
  5. Pull the print cartridge toward you out of its slot.
s.gif Step two: Install the netest page printing at the time of printer powered - c00312625.gifidge minimtop.gif
  1. Remove the new print cartridge from its packaging atest page printing at the time of printer powered - c00312564.gifeful to touch only the black plastic, gently remove the plastic tape by using the pink pull tab. Figure 6: Remove the tape c00312625.gif 1 - Copper-colored contacts test page printing at the time of printer powered - c00316911.gific tape with pink pull tab (must be removed before installing) 3 - Ink nozzles untest page printing at the time of printer powered - s.gifape CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.c00312test page printing at the time of printer powered  - minimtop.gifss=
  2. Slide the new print cartridge forward at a slight upward angle into the empty slot. Using your index finger, push the print cartridge forward until it clicks into place. Figure 7: Insert the print cartridge c00316911.gif
  3. Close test page printing at the time of printer powered - c00316913.gifor.
s.gif Step three: Align the print cartridges minimtop.gif If you are installing a new print cartridge, the product begins to print a print cartridge alignment sheet. This may take a few minutes.
  1. Lift the lid of the product.
  2. Place the top of alignment page face down in the left front corner of the glass. Figure 8: Place the alignment page face down c00316913.gif
  3. Close the lid.
  4. Press the Scan button.
  5. The On/Resume light will blink during the alignment process.
  6. After the On/Resume light stops blinking, alignment is complete.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to clean head HP 7260


HP Photosmart 7150 and 7260 printers




  1. Make sure plain paper is loaded into the In Tray.



  2. To perform the first level cartridge cleaning is a spit and wipe, press and hold the Power button while pressing the Cancel button twice, then release the Power button. The printer will generate a series of noises as it performs the cleaning.


  3. Print a test page from the computer.


  4. Once the cleaning has completed and the test page has printed, examine the test page. If the print is not clear and/or there are lines in the color bars, continue to Step 5.If the print quality is acceptable, disregard the subsequent steps.


  5. To perform a second level cartridge cleaning, press and hold the Power button while pressing the Cancel button twice. Release the Power button and press the Resume button. The printer will generate a series of noises as it performs the cleaning.


  6. Print a test page from the computer.


  7. Once the cartridge cleaning has completed and the test page has printed, examine the test page. If the print is not clear and/or there are lines in the color bars, continue to Step 8.If the print quality is acceptable disregard the subsequent steps.


  8. To perform a super clean, press and hold the Power button while pressing the Cancel button twice. Press the Resume button twice then release the Power button. The printer will generate a series of noises.


  9. Print a test page from the computer.


  10. Once the super clean has the completed and the test page has printed, examine the test page. If the print is not clear and/or there are lines in the color bars, continue to Step 11. If the print quality is acceptable disregard the subsequent step.


  11. To perform a pen nozzle test, press and hold the Power button while pressing the Cancel button eight times. Press the Resume button four times then release the Power button. The printer will generate a series of noises then print a page displaying a test pattern. If there are gaps in the printouts the cartridge(s) may need to be replaced.

Jan 17, 2015 | HP PhotoSmart 7260 InkJet Printer

2 Answers

I have an hp 3150 all in one printer. Every time I turn it on to print a document it prints a test page. I am out of color ink so it doesn't print the additional numbers and lines to align the printer. I...


I know your problem and i want to know that have you changed or refill your cartridge?.

if yes
place one plain paper in the tray.
it will print the test paper
print it and place it on the scanner with the printed side down.
press the scan button from the printer
printer will blink the light for some time and stop blinking
now it didn't print test print every time you print

thanks

Jun 26, 2010 | HP PSC 1315 All-In-One InkJet Printer

2 Answers

How to print only with black catridge


go to print then properties then advanced and put a check on the "use black ink only" option

Mar 06, 2010 | Epson Stylus Photo R220 InkJet Printer

2 Answers

My printer keeps printing the test page every time it's switched on. I have C3180 all in one printer.


That is a "configuration-option" -- navigate through the controls on the printer itself to disable that option; or, just leave the printer on -- it will go to "power-save" mode after a few minutes of non-usage.

Dec 14, 2009 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

I have a brother hl-5250dn with an extra tray for legal size paper. I have a problem printing loan documents sent via swiftview or elynx. I can only print on letter pages or legal pages but not both and...


Sounds like your secratery's printer is set to ignore paper mismatch errors. It depends on the setting you have in your driver. Can you set your driver on your printer to ignore paper mismatch errors. If not when your printer errors, just try hitting the go button and it should print the document any way.

Sep 07, 2009 | Brother HL 5250DN Laser Printer

1 Answer

Problem with printing test page every time switch on


hi,
this is kshitij
just scan the test page then test page will not be printed every time when all of you power on the printer.

Feb 23, 2009 | HP PSC 1410 All-In-One InkJet Printer

1 Answer

Printing three test pattern pages on every power up


that means that the clean and calibrate was incomplete after replacing the one print cartridge

May 28, 2008 | HP DesignJet 100 Plus InkJet Printer

10 Answers

Keep printing test sheets


A lot of HP printers print a page to enable the print head alignment and calabration. This normally orcurs when a cartridge has been changed. If the alignment page fails then it will reprint alignment page until it can align.

So, you need to get that page it prints and place it on the glass and press scan, then it will complete alignment and be ready to rock.

See Here

Cheers

Jan 19, 2008 | HP PSC 1510 All-In-One InkJet Printer

10 Answers

My printer keeps printing the test page every time it's switched on


0.gif Re: HP PSC 1513 all in one by Bert t.gif (9/25/07 1:07 PM) reply + / - http://h10025.www1.hp.com


0.gif Re: Re: HP PSC 1513 all in one test page always pr by Anonymous (12/12/07 6:14 AM) reply + / - Subject : How to disable the test page that always prints when you switch on the HP PSC 1513 all-in-one printer.

Take the test page ( also called : alighnment page ) that always prints when you switch on the printer and place it face down in the scanner.

Then press the scan button on the printer itself.
(this is the button at the bottom of all the buttons on the printer/scanner.)

Make sure that the printer scans the test page.
( sometimes you press the butoon and it doesn't scan )
( it makes a scanning noise when scanning succesfully )


Then it will stop printing the test page ( alignment page ) ever again.

This is a really stupid product feature on HP's part to waste ink and force people to buy more cartriges.


beukes2@gmail.com

Nov 29, 2007 | Office Equipment & Supplies

Not finding what you are looking for?
HP PSC 1410 All-In-One InkJet Printer Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...