Question about HP LaserJet P3005 Printer

1 Answer

Standard top bin full remove paper

Sir,
when i on the printer then "standard top bin full pls remove paper"
shows massage. I have HP laserjet printer 3005 dn . so how can i solve this problem.

pls help me standard top bin full

Posted by on

  • Anonymous May 14, 2009

    This happens on our printer daily. Push the flap down on the exit tray

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Greets!

Firstly, is the exit bin full of paper? If it is, just remove it.

If not, then it's going to be a sensor that recognizes the paper amounts in the exit tray. Check for broken plastics and possibly stuck plastic flaps in the exit tray.

If it's neither of those, try turn it off, unplug, then reverse.

Other than that, if no go, then it's an internal sensor issue. At that point, probably the best bet is to replace as repair costs would outweight a new unit cost most likely.

Posted on Feb 27, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jaylex
  • 417 Answers

SOURCE: standard top bin full remove paper

Hi there is seems that the machine thinks there is too much paper at the paper printout exit. If there are printouts on the top of the printer remove them and the printer will start printing or the error message will go away. If there is nothing on top of the printer then where the paper comes out after it has printed you will see a black plastic lever type it is more likely to be in the up position without breaking it if it hasn't already been broken move it so it is in the down position it is on a hinge so be careful and it should sit at an angle. Once this has been done the printer will reset the message itself.

Hope this is help you oh if the arm is broken it will need replacing (just the arm)

Thanks J

Posted on Jan 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer shows standard top bin full


Where the paper exits, there should be black tabs that lift up each time a page exits. They might be stuck in the up position, or possibly broken. Usually caused by aggressive removal of a paper jam.

Sep 24, 2014 | HP LaserJet 5200 Printer

1 Answer

Can not print. Standard top bin full shows up on the display


Clean top bin sensor.
Remove back cover., observe a flip moving up & down while paper is coming out & the same was fed into a ir sensor., u can see from back side., clean that sendor with good brush or cloth..

Sep 24, 2014 | HP LaserJet 5200 Printer

1 Answer

Hp 5550n error - standard output bin full please remove all paper from bin


After print paper reaches upper bin, you can observe a flag moving while paper coming out. once this flag is stopped moving printer treates bin full..check the flag is moving freely. open top cover clean this sensor.

Sep 21, 2011 | HP Hewlett Packard LaserJet 5550n Printer

1 Answer

When i on the printer then "standard top bin full pls remove paper" shows massage. I have HP laserjet printer 3005 dn . so how can i solve this problem.


You have a broken sensor flag most likely or a defective sensor. Sensor and flag located under the top cover in the top right hand back corner. Also check to see if the cable is connected on the sensor and DC controller. If everything is ok, mostly likely defective DC controller.
Often I do repairs on printers because the customer does not use it properly or just plain abuses it. Just read the manual before using.

Aug 25, 2011 | HP LaserJet P3005 Printer

1 Answer

When i on the printer then "standard top bin full


Just check at upside where paper iscoming out after print, there you can see the two black flips to monitor the paper out position, this flag sensor got dusty this error apprears, remove back cover, you can observe left side this sensor, just clean it..

Aug 25, 2011 | HP LaserJet P3005 Printer

1 Answer

Issues with HP Laserjet P3005n


That means that the output tray is filled to capacity, or one of the students broke the "bin full flag" at the top of the printer.

Feb 24, 2010 | HP Hewlett Packard LaserJet P3005n Printer

2 Answers

Standard top bin full remove all paper from bin


Check the sensor flag where the paper exits the printer and make sure it is not stuck in the "up" position. This is a small black plactic flap right in the center of where the paper exits. When this flap is up it tells the printer that this area is full. HP says to "flip" the sensor flag up and down to make sure it is not stuck.
Good Luck

Nov 25, 2009 | HP LaserJet P3005 Printer

10 Answers

Standard top bin full error in hp 5200 tn laserjet printer


i have hp 5200 printer
printer shows message top bin full
and not prints what slution of this error

Aug 28, 2008 | HP LaserJet 2420 Printer

1 Answer

Hp 3800dtn standard top bin full remove paper error


top bin full error is hte lever sensor where you see the paper coming out, the lever is stuck in the up position.

It's used to tell you to remove the paper from the exit because it's too full.( Too many copies on the top)

Jun 27, 2008 | HP Color LaserJet 2600n Printer

6 Answers

Standard top bin full remove paper


Hi there is seems that the machine thinks there is too much paper at the paper printout exit. If there are printouts on the top of the printer remove them and the printer will start printing or the error message will go away. If there is nothing on top of the printer then where the paper comes out after it has printed you will see a black plastic lever type it is more likely to be in the up position without breaking it if it hasn't already been broken move it so it is in the down position it is on a hinge so be careful and it should sit at an angle. Once this has been done the printer will reset the message itself.

Hope this is help you oh if the arm is broken it will need replacing (just the arm)

Thanks J

Jan 12, 2008 | HP LaserJet 2420 Printer

Not finding what you are looking for?
HP LaserJet P3005 Printer Logo

2,833 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...