Question about Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Navnet VX2 System won,t power up, have voltage at plug in. Are there any fuses that might be out ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Remove all connectors aside from the power cable then attempt to power up. If the unit turns on, it may be your radar if you had one one it originally. If so plug the radar cable back into it with it off and try powering up. If it does not, then thats the issue. the Radar or your cable.

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the "toolbar" from the top of the screen on my furuno NavNet Vx2?


go to toolbar with controller, and push clear key. just it.. but when you restart your system, it appears again. if you wanna lose it anytime, you must do it inside the General Setup.

thanks..

Dec 21, 2012 | Furuno NavNet vx2 1920C GPS Receiver

3 Answers

Ais and 1920c Furuno chart plotter


n the system setup, under “UNITS” I set BEARING to “MAG” (magnetic). This will cause the unit to display course / bearing information in relation to the Magnetic North and match magnetic compass readings. It is not the same as True North! One has to be careful with this setting. There are a number of areas where the earth's magnetic field is locally disturbed, sometimes very significantly. Your GPS may not account for it. - again, under “UNITS” I set “METRIC”.

Sep 02, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

I want to do a master re-set on a Furuno Navnet 2 , 1944 radar/plotter. Do you know the sequence of keys? Andy


Press and hold the alarm key whilst powering up. Also try it with the clear key while powering up again.

Sep 05, 2010 | Furuno NavNet vx2 1944C/NT GPS Receiver

1 Answer

How do i connect my furuno navnet vx2 to my vhf radio. i have a 6 pin nmea cable for the vx2. but i do not unerstand which wire to use.


the output is on the black (blue) and white wires. in system setup, portsetup, you can select which sentences it sends out. 847-746-0100

Jun 17, 2010 | Furuno NavNet vx2 GP1720C GPS Receiver

1 Answer

How connect the nav net vx2 to autopilot simrad.what output port and colour cable


Get someone from a marine electronics company to do this for you. If you are unsure of the basics of what you need and you attempt to do this while going in blind, you may ruin your nmea ports on your navnet and autopilot. While I understand that you are trying to save $$$ by doing this, there's more to it than just wiring. There are port setups and nmea sentences to enable etc.

Jan 18, 2010 | Furuno NavNet vx2 GP1720C GPS Receiver

1 Answer

My furuno navnet vx2 periodically freezes during operation and must be restarted. Any suggestions?


Reinstall the operating software. The unit should probably go to Furuno.
Try operating it with only a GPS connected (no radar, no network). If this resolves it, it is almost certainly software. It could be low voltage or failing mother board.

Jul 15, 2009 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

Adapt 997c si gps to navnet furuno sounder


no can do you must have a Furuno GPS or a GPS with NMEA 0183 output. you could get that from the Hummingbird display but not straight from the antenna

Feb 27, 2009 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

I would like to purchase a full Furano Navnet 3D system with for my 42' sailboat now in production. It does not have hydraulic steering though. Is there a hydraulic linear drive compatible withe Furuno...


No, you will use the appropriate Simrad Drive unit such as an HLD350. It comes in long and short throw and split versions, and dual ram versions. Better to discuss on the phone probably. 847-746-0100 or email support@technicalamrine.com

Aug 09, 2008 | Furuno NavNet vx2 1920C GPS Receiver

1 Answer

I can not seem to get a simrad ap 20 to recognize the nmea connection from the navnet vx2


you will have to designate which sentences to send to the AP20 from the navnet under port options. also make sure the AP20 is set to read the correct port to accept the information such as gps1 or 2 or nav1 or nav2

Jun 29, 2008 | Furuno NavNet vx2 1920C GPS Receiver

Not finding what you are looking for?
Furuno NavNet  vx2 1920C GPS Receiver Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Furuno GPS Devices Experts

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Steve
Steve

Level 3 Expert

688 Answers

Are you a Furuno GPS Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...