Question about Frigidaire FWTBB30DS Front Load Washer

2 Answers

Code F03 my washer machine model FWTBB30DS (frigidaire gallery front load)write the F03 code after few minutes running, in any mode. thank you steve

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

I just had this same problem, it was a bobby pin stuck in the drain motor.... hope this helps

Posted on Mar 29, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Frigidaire Master
  • 3,361 Answers

Typically a low water or no water coming in problem. Sometimes a drain problem.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer cuts off at 7 minutes and will not do the


It be the carbon brushes are worn down on the motor, when it goes into the final spin.

Mar 09, 2010 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Front load frigidaire washer w/ error code F03....doesnt want to drain. Tried spin/drain, delicates, and normal and all end up with F03!! Please help!!! Thanks Royce


The F03 code is a problem with your water system. your inlet valves may have failed.

Open up the bottom panel and you will find a tech sheet that explain the codes and gives trouble shooting techniques. here is the service manual, good luck, hope this helps......

http://frigidaireservicetips.com/pdf...icControls.pdf

Jan 06, 2010 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Wont drain water out frigidaire gallery model fwt449fs2


at the very bottom on the front panal you will find two screws, take those out, the panal will drop out of place
rith there on your right, you will see the pump
put down a few towels
disconnect the hoses and make sure the pump and motor are clear

Oct 18, 2009 | Frigidaire FWTBB30DS Front Load Washer

1 Answer

Dirt streaks appear after laundering


Grease seal for the bearings need to be replace. Unless you are a DIYer this is an expensive repair. Labor to install a new grease seal is about 400 to 500 dollars depending on the area. Parts will run about 100 to 150 dollars. The grease seal is cheap about a $10.00 part, but since ypou have the washer torn apart, and the grease seal has fail, you should also replace the bearings.

May 17, 2009 | Frigidaire FWTBB30DS Front Load Washer

1 Answer

Front load washer


Possibly the door switch...check for adjustment or replacement

Apr 18, 2009 | Frigidaire FWTBB30DS Front Load Washer

1 Answer

Washer fills washes then won't spin or rinse model FWT867GHS front load


does it empty after wash if not then pump or filter may be blocked

Jul 14, 2008 | Frigidaire FWTBB30DS Front Load Washer

1 Answer

WATER LINKING AT THE BOTTOM


Had same problem, found a 4 inch hose on left rear leaking, not properely installed. This corrected the problem after making correction.

Jan 17, 2008 | Frigidaire FWTBB30DS Front Load Washer

1 Answer

Kenmore 44072 Front Load Washer help


my kenmore washing machine has the timer out of time

Aug 08, 2007 | Kenmore 44072 Front Load Washer

Not finding what you are looking for?
Frigidaire FWTBB30DS Front Load Washer Logo

418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...