Question about Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag top loading washer won't agate. Instead it fills with water and spins, then drains, fills for the rinse and spins. Thanks Bill

Posted by on

  • xyrn99 Mar 02, 2009

    Yup, I have the same problem too! It just started doing this tonight. ahhhhh,

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 3,361 Answers

Open your control panel.
Disconnect then reconnect your timer wiring harness.
If this does not correct the problem,replace the timer.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My maytag mtw5600tq1 washer won't hold water. Its


Hi,
Its sounds like you have a siphon going on, this happens when the drain hose it too low during fill and as the water enters the unit it exits through the drain hose. To stop this the drain hose needs to be higher than the tub itself, meaning: raise the drain hose behind the washer to about control panel area. This will or should stop the siphon effect and allow the water to remain in the tub. If the drain hose is low this siphon will start again.
I hope this helps

Aug 26, 2011 | Maytag Washing Machines

1 Answer

My 3 year old Maytag SAV5710AWW top-load washer


It is your water pump. If you don't know what you are doing it could be tough.

Nov 20, 2009 | Maytag SAV5710 Top Load Washer

1 Answer

Kicking out water during wash cycle - spin instead of agitation


Hi,
Try these

  1. Check the drain hose, it should be at least as high as the top of the wash tub, about 38 inches.
  2. The drain hose must sit loosely in the house drain. Do not seal the air gap around the drain hose or a siphon will occur.
  3. Check the drain control lever
  4. Test the drain control coils
  5. Check the cam bar
pls rate my suggestion..

Jul 19, 2009 | Maytag LSE7806A Top Load Stacked...

3 Answers

Water fills to proper level but agitator doesn't come on instead there is a grinding noise, when I move control to just prior to rinse cycle water drains properly, but still just grinding or buzzing n


Hi, Do you know if the washer spins at all?
It sounds like the coupler has gone bad.
Please let me know if it spins at all.
I can send yyou instructions on changing the coupler.

Vic

May 28, 2009 | Whirlpool LTE6234D Top Load Stacked...

2 Answers

Maytag Atlantis MAV6200AWW Washer Problem?


I HAVE AN ATLANTIS MAYTAG WASHER . I HAD THE SAME PROBLEM AND I SOLVED AS FOLOLWS. REMOVED THE MOTOR, I APPLIED GENERAL PURPOSE GREASE ON BOTH SIDES OF THE SLIDING MOTOR SURFACE PLATE (MOTOR BASE) . THE GRASE HELPS THE MOTOR TO SLIDE BECAUSE AS YOU KNOW THE MOTOR DOES NOT HAVE ANY ADJUSTMENT. TRY IT PLEASE . GOOD LUCK

Feb 20, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Maytag Top Load Washer - clanking noise when spinning


no spin cycle or agatator movement , fill cycle and pump cycle works

May 31, 2008 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

Washer is not filling during rinse cycle.


Sounds like the water is being siphoned out by the drain hose. Check to see if the drain hose rises above the top of the tub.

Oct 29, 2007 | Maytag Performa PAV2200

Not finding what you are looking for?
Maytag Atlantis MAV6000 Top Load Washer Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...