Question about Vehicle Parts & Accessories

4 Answers

Telko s002 manual

I need manual for telko S002 I have forgotton code and when replacing battery cannot stop alarm going off because i dont know code.

Posted by on

  • annbry Feb 26, 2009

    I have been advised to contact Manf. for manual, however i dont know how to contact.
    I hoped some other user wouldbe able to assist

×

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,952 Answers

PROGRAMACION DE LA ALARMA TELKO MODELO S001/S002

To program security code alter battery installation

  1. Press the digit ?0?
  2. Press the ?*? button
  3. Enter your new code number. (1 a 12 digits)
  4. Press the ?*? button

To change existing code to a new code

  1. Enter the old code number
  2. Press the ?*? button
  3. Enter your new code number. (1 a 12 digits)
  4. Press the ?*? button

Operation ? Model S002

  1. To arm the S002, enter your security code followed by the ?#? button. You will hear a short beep and the LED indicator will illuminate for a few seconds. The unit automatically arm itself after no motion has been detected for approximately 2 minutes.
  2. To disarm the S002, enter your security code followed by the ?#? button. You will heas a short beep to verify the unit is disarmed. You have approximately 15 to 30 seconds to turn off the unit before the alarm sounds once you have entered the detection area.
NOTE: When the S001 and S002 are in ?armed? mode, and movement is detected, the unit will wait silenty for 15 or 30 seconds then sound it`s piercing 110 DB siren. Whitin this 15 second period, or the alarm is sounding, you can disarm the unit by inserting the key and turning to the ?OFF? position (Model S001) or by entering the security code followed by the ?#? button (model S002). If the unit is not disarmed, the alarm will sound for 60 seconds then automatically reset to the armed mode. If the unit detects motion, the alarm will sound again and then reset. The cycle will continued as long the unit remains armed.



telko s002 manual - 0%20stars_w.png

Posted on Feb 25, 2009

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

Http://www.blinks.biz/S002.html please use this link thank you for useing fixya please rate me

Posted on Feb 26, 2009

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Vehicle Part... Master
  • 13,433 Answers

Hey,

Have you called your dealer? they should be able to provide you with the code with proof of purchase but I will look around and see if I can find this for you.

Posted on Feb 25, 2009

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,550 Answers

You need to contact manufacturer to get the manual .

There is no online manual for your product

Posted on Feb 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 97 tahoe with crime stopper sp101 alarm. truck was working fine until i put a new battery in, now gas gage is going haywire,and no signal to fuel pump. any solutions, or suggestions. i know its...


when u disconnected the battery you activated the alarm system which has a fuel shut off you need to reset the alarm system ,,check the system for a malfunction [could have received a power surge when battery was hooked up] or remove the alarm system

Aug 13, 2013 | 1995-1997 Chevy 1500 Truck Ignition...

1 Answer

My 2000 grand vitara alram wont stop going off what can I do to stop it


a lot of times car alarms go off when they since a voltage drop in the vehicles battery test or replace cars battery

Jun 01, 2012 | Excalibur. K9-MUNDIAL-SS Entry Level Auto...

2 Answers

How do program a ca5blctx remote


The program manual can be downloaded at the following link:

Code Alarm 5BLCTX program manual

Jan 24, 2011 | Vehicle Parts & Accessories

1 Answer

Car alarm goes off after locking the car.sometimes ten minutes smoetimes three hours after but it still goes off ive disconnected the alarm horn for now but still get the siren noise.i dont know what to...


How old is the alarm? If you have glass breakage detection or motion sensors installed one of these could be faulty. If the alarm is more than a year old and it's an after market alarm it is possible the alarm is faulty and needs to be replaced. There is a fuse in the power supply line, usually running along the firewall between the power point and the alarm. Remove this fuse and the alarm should be deactivated but the ignition kill switch will not be active so you can use the vehicle and the siren will stop going off.

Sep 09, 2009 | Vehicle Parts & Accessories

1 Answer

Keys have stopped working properly, will lock


Manual unlock door start car. The car battery was low and could not respond to key. If it win't start charge or jump it. Do not disconnect the battery unless you have to some systems require special codes for radios and other equipment. You may have to get the auto club to open the door for the hood release and jump you there. I don't feel bothe remotes batterys went bad at the same time but. The last resort is to change one and try it. Don't expect radio shack to replace your battery for your remote try calling a locksmith or the dealarship. Some dealerships are quite helpful...depends on where you live.

Aug 17, 2009 | Vehicle Parts & Accessories

1 Answer

I have a car fitted with a Clifford GS 470 alarm but I cant get the alarm to stop. The car that this alarm was fitted in has not been started in 5 months and so the battery ran flat. I replaced the battery...


you might have to replace the batteries in the remotes. The reason why the alarm is going off because once you plug power back to the alarm brain it sets the alarm off and the only way to make it stop is to hit the unlock button the remote. Make sure all connections on the alarm brain are good and try changing the batteries in the remotes. also might have to reprogram the remotes to the brain if it has been sitting for awhile.

Feb 16, 2009 | Vehicle Parts & Accessories

2 Answers

Toad sterling car alarm lost manual and need stop code.


This worked on my car when the clicker died:

Put the car in valet mode. Disconnect the NEGATIVE battery terminal. Put the keys in the ignition and turn it as far forward as you can (as though trying to start it) and let it spring back. Reconnect the negative terminal. This should reset the alarm to valet mode. Programming varies from brand to brand. Contact an alarm dealer and they can help reprogram the remote(s).

Oct 17, 2008 | Vehicle Parts & Accessories

2 Answers

No response when i try to lock/unlock the car alarm


try changing the battery first....if it's still not functioning properly then maybe your shock sensor is defective already...go to a car accessories shop that installs car alarms...you could have them check your alarm first and they would know if your alarm could be repaired or not...good luck.

Oct 07, 2008 | ' II' DIY Car Alarm Vehicle Anti-theft...

Not finding what you are looking for?
Vehicle Parts & Accessories Logo

Related Topics:

1,005 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13213 Answers

Brad Brown

Level 3 Expert

13732 Answers

Are you a Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...