a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Pop an empty bobbin on the thread spool. You need to disengage the motor from the presser foot so that the motor no longer makes the presser foot go up and down, but sends the power to wind a bobbin on the thread spool. Check with your machine's manual, but this is usually done be either pushing in, or popping out a button on the hand wheel. Begin a new thread on the bobbin following the directions either from your manual or as printed on the machine. On my Bernina, I have to push the thread spindle sideways to engage the bobbin winder. Use your foot pedal now and the bobbin will automatically fill up. It should stop when full, then you reverse your actions. eg: push the thread spool back, pop in the button on your hand wheel, insert the bobbin (check with your user manual as to clockwise-anticlockwise, and yes it DOES make a difference!) Re-thread your machine (always with the presser foot up) and make a test stich.
I hope this helps and happy sewing.
I'm thinking your machine is the type that needs to wind the bobbin with it in the carrier. Ok, here it goes. 1. Thread the top as usual and through the needle. 2. Open the needle plate. 3. Move the button on the left side of the carrier to the left and push down at the same time.
3. While holding two inches of thread apply pressure to the foot pedal and monitor the amount of thread on the bobbin. Don't overload! There is an outside red line to reference for this.
Each machine is different. Most of the machines that are electronic have a sensor to shut it off if you place the bobbin on the winder and push the winder into its position to wind. Give it a try. Also, check your spindle at the end to pull it outwards or attempt to untighten like you do a jar. This is the old mechanical machine but it is possible this machine uses it. Next you must look on your monitor for a particular symbol that represents the bobbin. This would likely be a button to turn it off and on.
Please first up on needle bar (Pressre foot). Then take one small screw driver or big needle put on bobbin center before some 3 or 6 times wring some thread ,then put on the bobbin machine wheel side after machine start slow and correctly you fill the bobbin.
place the bobbin the winder pull the thread from the spool around tinchoner wrap around bobbin push bobbin against stop turn leaver on wheel to release needle push down on peddle it will auto stop when bobbin is full.
Can you find the bobbin winder? You need to lift the "lid" and it is on the right-hand side - a small white spindle pointing towards you. Put a HV bobbin on the spindle. Look at the bobbin first - on one side the Husqvarna symbol is embossed - a crowned "H" in a circle. Be sure this H is facing you. Push the bobbin onto the spindle firmly, but not with so much force that you push the spindle into the machine (it takes a pretty big push to do that, but it has been done!) then using your right-hand thumb push in a downwards motion (towards the table). The spindle with the bobbin on it will go about one inch downwards. The bobbin winder is now engaged and you should have a pop-up on your screen. I often reduce the speed by two or even three clicks before I push the spindle down.
Pull the second thread spool - the one closest to the bobbinwinder - so it sits at a right angle to the machine. Put one of the spool holders (white plastic disks) - preferably the bigger one - onto this spool. This gives your thread a base to sit on. Put the thread onto the spool so that the thread unwinds from the right-hand side (closest to the bobbin). Take the thread end directly across to the silver "button" that is near to the first tension slot on the left-hand side. The instructions say to wind it around this and then across to the bobbin winder, but I prefer to take the thread under the silver button, around the left-hand side and then across the top of the button (sort of figure-of-eight style). Just be sure the thread goes in beneath the button i.e. does not sit in a big loose loop around the button. The thread is then taken across towards the winder by going under the white plastic hook (looks a bit like a beak), then up and over the top of the next little silver button (smaller than the other one). Then you wind the thread around the bobbin four or five times and take the thread end over to the cutter located directly to the right of the bobbin winder. Cut the thread (if it is too short to be cut, just leave it flop down) and press the Start/Stop button. The bobbin will fill and stop of its own accord when it is done. If it does not fill right up or is uneven (more on one side than another) there is a fix for that too. Write back here if you need to do this. Don't forget to take the speed back to normal before sewing. You can wind the bobbin from the needle but be sure you have a metal foot on, not one of the plastic ones. Personally I find I get a better bobbin wind the way described above and it only takes a few seconds to re-thread ready for sewing. I tend to have a big bobbin winding session and do lots of bobbins at once, especially embroidery bobbinfill. At any one time I would have at least six bobbins filled with bobbinfill and a dozen of various thread colours for normal sewing.
Do hope this helps you. Write back if this is still not clear. Did you try to Google for a video of this? I have never looked for one, but it is very likely that someone has made a video and made it available online.