Question about D-Link Express EtherNetwork DP-301P+ Print Server

1 Answer

D-Link DP-301P+ Print Server issue

I went to hook up a D-Link DP-301P+ Print server and all 3 lights are lit up continuously. I know it's a DRAM error. Is there any way to recover the print server from this state? This is for a small office plotter that they need to use about 3-4x a week. Any suggestions?

Posted by on

  • Anonymous May 16, 2009

    I have the same problem. The 3 LEDs are turned on continuously and I can not connect to Any solution?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 3 tips or uploaded 2 video tips.


    An expert whose answer got voted for 20 times.

  • Expert
  • 167 Answers

- Kindly try to update the firmware of the Print Server.

Posted on Mar 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I want to reset the print server D-Link DP-301P+. I forgot IP address which I was changed according to network settings.

There are two steps that we can suggest,


1) Install the psadmin software if you have not already. If you have lost the psadmin software then search for it on the web.
2) Start the psadmin software and click "factory reset".
3) If the software demands a password, try "SYSxxxx", where xxxx stands for the last four digits of the MAC address located on the underside of your server. (Example: if your MAC address were "63 XE 29 44 F2 96", then your password would be SYSF296.)
4) Click yes to confirm the reset.


On the back of the print server you will find a pin hole, insert a paper clip for 30 secs with the print server powered on. All lights will flash. Try to setup the server again.

Hope this helps.


Jun 01, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I have connected the d-link to a KOT printer,my network cannot find the server.And according to the manual I cannot browse the default ip of the DP-301P+ sever.please assist me immediately.

I have D link DP- 301P Print server I am using it in Epson M188D Printer for KOT Printing but its shows some times printer not found on network, please help me to solve the problem.

Mar 22, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I have print server DP-301U Pls let me know the default IP address for configuration

As far as I can remember the default IP is 192.168.0 .10, subnet
If this isn't the correct IP address, you'll need to reset the d-link print server Hope this helps
Regards, c0d3

Feb 09, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

No light at all including power light

Check your power supply. If the transformer box is cold and the outlet has power, you'll need to replace it. You will need DC 5V, 2.5A and the correct adapter. Thus check with Dlink if your print server is still under warranty.

I hope this helps.

Cindy Wells

Dec 11, 2009 | D-Link DP 301P (DP-301P) Print Server

2 Answers

How to reset the administrator password of the D-Link DP-301P+

i forgot password Printer Server D_link Dp-301p
Please Help Me

Jul 30, 2009 | D-Link DP 301P (DP-301P) Print Server

1 Answer

I would know if D-Link DP 301P Print Server supports SNMP protocol because i need to print from IBM iseries thank you

It supports all below protocol so you can give print from IBM iseries .

TCP/IP Protocols Supported :
  • SNMP
  • Telnet
  • TFTP
  • FTP
  • LPD
  • RARP
  • DHCP

Jul 28, 2009 | D-Link DP 301P (DP-301P) Print Server

1 Answer

DP-301P+ Express EtherNetworkTM Fast Ethernet Print Server

You need to connect to it (using the broswer at the PC of same LAN with the current ip of the print server). Then click on Tools TAB, click on "Reset" at left. You should see "Do you want to restore this device to factory default setting?". Click on "Apply"

Jun 04, 2008 | D-Link DP 301P (DP-301P) Print Server

1 Answer

Forgotted the Ip of D-Link DP 300U print server

You may use the PSAdmin software to configure your print server even if you don't know the IP address. The only requirement is that the DP-300U has to be in the same network (subnet) as your PC running PSAdmin. In the PSAdmin, you will then be able to view or change the IP address.

Here is the link to download PSAdmin:

Remember that if you also have forgotten the Admin password, you will have to ship the unit to D-Link in order to have it factory reset.

May 10, 2008 | D-Link DP 301P (DP-301P) Print Server

1 Answer

No printing threw terminal service

do you have the options set correctly on the remote computers assistant to use local devices

Dec 25, 2007 | D-Link DP 301P (DP-301P) Print Server

Not finding what you are looking for?
D-Link Express EtherNetwork DP-301P+ Print Server Logo

Related Topics:

852 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18419 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides