Question about Cisco Catalyst 6506 chassis Networking Switch

1 Answer

The ping response time is very bad on Cisco 6506.

During test between a PC and the Cisco 6506 switch the response time is unacceptable. What could be the problem please?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 80 Answers

It should be Layer 1 Issue (Physical connection). Your cable, PC's Ethernet card or the Interface in your Cisco it self.

P.S.: If this information was helpful, please rate this solution. The ping response time is very bad on Cisco 6506. - aymloekh0fg4hpz2e87n86udvs4fowqwshuaaaaasuvork5cyii=

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem with cisco sg500


I'm not familiar with the device, but it might be something in the configuration. It could be DHCP, it could be something deeper.
I suggest contact Cisco support directly, they have support forums too.

Dec 11, 2013 | Cisco Small Business 500 Series Stackable...

1 Answer

My lan speed going down.i am using cisco router 881, guide me to troubleshoot this speed issue


this could be MANY reasons....first, how many devices on your LAN ??? If there is a broadcast storm, that will slow things down on your LAN. Very few devices nowadays cause this. Also, from your pc, try pinging your router using an increased packet load. So start of with ping <router ip> -l 8000 and try going up to 20000. In theory, you should not be getting any loss. Responses times up to 12000 should be 4 - 8 ms. Higher response times point to errors on NICs. On the route console, try a show int VLAN <vlan number you've configured for your LAN> and enter. Under the CRC Errors and Interface resets, if you have anything more than 5, it could be a cable/NIC/MTU size problem.

Jul 08, 2013 | Cisco 881-K9 Router

1 Answer

My cisco 877 dsl router sometime disconected from internet itself and after 5 or 6 hours its return back what can be the problem


1. check the status to the router page by logging into the router to see if the router lost connectivity.
2. Pinging an outside address will tell you if you have lost connectivity with the ISP or not.
Ping test = Ping www.yahoo.com
this is within the router

Apr 19, 2010 | Cisco 877 ADSL Security Router

1 Answer

ICMP packets not working on Dell Latitude D620


With vista I had the same problem, but when I enabled network fileshareing and set up some network drives it started to answer on ping requests, so it should be one of the networking protocols to enable.

Jan 14, 2009 | Dell Latitude D600 Notebook

1 Answer

Siements 5890 router


When you say HQ is that outside on the wan port trying to ping the Lan port?
Sometimes the router itself will respond to a ping but will not pass ping requests thru as the internal firewall can never be fully shutoff unless you are running your cisco switch as a DMZ 
also are you connecting your other pc's to the cisco or to the 5890.
Instead of shutting off the firewall completely try enabling bridge mode and give your cisco the outside IP addy.

Apr 30, 2008 | Computers & Internet

1 Answer

Cat OS 6513 module deteced but not shown in show config


I had this same problem on a switch a while ago. what version of CATos are you running on this switch. the blade you are using might not be upto date.

I had a 6506 with 10/100 modules/ upon installation of 10/100 with inline power the chasis would not detect it but would detect the board.

I updated the CATos version and it worked

Feb 18, 2008 | Cisco Catalyst 6513

Not finding what you are looking for?
Cisco Catalyst 6506 chassis Networking Switch Logo

Related Topics:

353 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

brian soufane

Level 3 Expert

693 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18346 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...