Question about Connex 4600 Base CB Radio

2 Answers

Owners manual for connex 4600 turbo

I need to know if i can hook this radio up to the cb power supply that runs off the battery thru the fuse panel to the radio or if i need to go straight to the battery

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

To cut down on noise i would hook it directly to the battery. make sure there is a fuse in the power cord first.

Robert

Please rate this solution thanks

Posted on Feb 23, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem with the white noise. but yes i hooked it up to the in cab power supply in my volvo big trk. power is fine . again you do have increased white noise. but hay i got a company trk. tks

Posted on Apr 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a connex 4600 turbo cb radio operate cool enough in a dash enclosure?


I would say yes it has a large heatsink. The variable might be the tuning. But if it's amp is not being pushed any harder than factory you will be fine. Nice radio I prefer them over the 4400turbo and the 3600hp it has the board like a 4300 not the 3300s like the fore mentioned.

May 26, 2014 | Connex 4600 Base CB Radio

1 Answer

Connex 4600 turbo need too know what size power supply I need too run this as a base


sizing a power supply is simple.....look at the fuse in the radio, and add about 40-50% to it, and look for that size psu

Feb 15, 2014 | CB Radios

1 Answer

Looking for a manual for my Connex 4600 Turbo


have you tried CB Tricks .com they should have what you're looking for if you take your time to find it there.

May 11, 2010 | Connex 4600 Base CB Radio

1 Answer

Connex 4600 turbo radio stays keyed up even with mic disconected


Bad RX/TX Transistor? I don't have a diagram for the 4600. Sorry!

Mar 28, 2010 | Connex 4600 Base CB Radio

3 Answers

Connex 4600 turbo. Poor receive. About 4 mi.


Hi there!!

The Connex 4600 Turbo is a very sensitive radio these radios don't work good at all with the stock microphone! The best microphones are the RK-56 and or the Astatic 636L which most people use and you shouldn't get any squeal. And make sure if that you are using an external speaker get it as far away from the radio as you can facing away from the radio so it wont feedback. As far as a Mod kit there are several ways to modify the radio which most are pretty hard and drawn out. but the most easy that used to be used is as simple as a diode placement in the right place which is old school but still works good. You must be very careful as if you are to slightly touch the wrong points the radio could be destroyed and no longer work so caution is to be taken if you don't know what you are doing please don't try it on an expensive radio!! If you want more info on the mod e-mail me

never the less a Modulation kit or modification wont help your Receive it will only help your Transmit signal!!

Dennis

May 20, 2009 | Connex 4600 Base CB Radio

4 Answers

Connex 4600 Turbo


i have the same radio turn talk back off and there is enough power ull have talk back through you trucks radio speakers and it needs to be hooked up to the battery with at least 12ga wire

Feb 10, 2009 | Connex 4600 Base CB Radio

5 Answers

Frequencies


i have a 4600 connex and if i turn the mic gain all the way up i get alot of modulation.can someone tell me how to fix that?

Feb 01, 2008 | Connex 4600 Base CB Radio

3 Answers

Connex 4600 turbo export radio


Hi,

On most mobile communications equipment, it is best that:
1. the power leads are directly wired to the battery terminals;
2. the bracket and radio body are grounded to the chassis of the vehicle;
3. a braided grounding strip be used in addition to the negative power lead; and/or
4. a gutter or trunk lip mounted antenna be used rather than magnetic. Antennas are better made of metal rod (not fiberglass) such as those made by Daiwa, Maldol, Oscar, Hokushin and others. The mount itself should use high quality RG58 coaxial cable such as those by Belden and others.

Hope that this be of some help/idea. Pls post back how things turned out or should you need additional information.

Good luck and kind regards.

Dec 31, 2007 | Magnum 257 CB Radio

Not finding what you are looking for?
CB Radios Logo

Related Topics:

1,057 people viewed this question

Ask a Question

Usually answered in minutes!

Top Connex CB Radios Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

489 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Connex CB Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...