Question about Acer Altos G510 Server

1 Answer

Is raid controller onboard - Acer Altos G510 Server

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 203 Answers

Yes. there is an integrated RAID controller onboard this server unit.
1 x RAID - integrated Ultra320 SCSI RAID 1

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error blue screen when installing


try a different graphics card (and if onboard graphics, try using a graphics card); you may also want to load hdd or raid controller drivers during the OS boot disk load (i.e. don't rely on MS drivers, use the mobo or vendor drivers)

Jan 15, 2014 | Fujitsu Siemens Computer Servers

1 Answer

I have got a 3 disk raid5 IBM xseries Server which does not boot. How can I resque data from these disks?


I'm going to go out on a limb and assume that you don't have a good backup of the data on your RAID array. So, generally speaking, the operating system is probably installed on a separate disk from your raid array (not a guarantee). But if this is so then you should be able to reinstall your operating system and drivers (esp RAID controller) to that (separate) disk and you're off to the races (replace this system disk if necessary). -OR- Depending on the make of your RAID controller you may be able to transplant your RAID controller into another machine and all the original drives along with it, so long as it has a battery backup and you place all the drives in their original order. If there is no battery backup on your RAID controller then DON'T PULL THE PLUG ON THE ORIGINAL MACHINE AND DON'T EVEN CONSIDER removing the RAID controller in any way. If you have any doubts, whatsoever, have someone with experience in RAID arrays do the work for you. It will be well worth it! (RAID arrays aren't for the faint of heart)...

Aug 24, 2011 | IBM eServer xSeries 225

2 Answers

Fetal error controller monitor failed x3400 ibm server


Welcome to fixya

Open the server and take out the raid controller . Now clean the slot as well as the raid controller . Now replug the raid controller check if it works

If you get same error now , then its time to replace the raid controller

Thanks

Oct 13, 2010 | IBM x3400 Server

1 Answer

I have Dell PowerEdge 2550 Server. I want to configure RAID, but I can't reach RAID MENU! I have DELL 2550 Server BOOT CD and Dell OpenMenage Server Assistant V7.2. All of them are running, but I...


RAID menu will either be CTRL-A (if you are using the onboard PERC 3/Di) or CTRL-M (if you are using an addin PERC 3/4). If you are not seeing either of these options, then you may not have it enabled in the BIOS. In the BIOS (F2), go to Integrated Devices and make sure that RAID is Enabled. In order to enable RAID, your server MUST have a RAID key, RAID memory DIMM (different from system memory), and a RAID battery.

Aug 12, 2010 | Dell PowerEdge 2550 Server

1 Answer

Enable RAID system


use this guide, this is fo the embedded sata raid controller that comes standar with the ml150 g5.

Enabling SATA RAID functionality in the BIOS Setup Utility: 1.Boot the server, and then press F10 to enter the ROM-Based Setup Utility (RBSU).
2.Go to the advanced tab.
3.Enter the IDE configuration or hard disk configuration.
4.Change the ATA/IDE configuration to enhanced or SATA controller 2 enhanced (if not available then use enabled mode).
5.Configure SATA as RAID or configure controller 1 as RAID.
6.F10 to save and exit.
7.Reboot the server.
8.During post f8 will now show up for the embedded SATA set up.
•Creating the RAID volume.
1.Enter the embedded SATA setup by pressing f8 during post.
2.Enter the array configuration utility.
3.Enter create array.
4.Create the raid volume as desired.
5.Save and exit.

i hope it helps you!!!

Aug 11, 2010 | HP ProLiant ML150 G5 Server

1 Answer

Wont boot says array controller wont start and no bios dell power edge 2500 server


Sounds like the RAID controller has failed. I would replace this first as RAID controllers are less expensive than replacing the system board, or the server as a whole.

Suggested: PERC 5i (RAID 0/1/5) or PERC 5iR (RAID 1 or 0 only)

Jan 03, 2010 | Dell PowerEdge 2500 Server

2 Answers

Raid 1


there must be some key on the startup to enter into the raid menu. And in that raid menu you can create raid .

Jun 23, 2009 | IBM x3400 Server

1 Answer

Scsi raid with battery backed memory for pweredge 2550 server


if my memory serves me correct i think this server uses a onboard (3di) card it is set in the bios to use the raid configuration, under integrated devices .make sure this is so ,as it boots press f2 key to enter.If this is so exit.next step is to shut the machine off pull the drives away from the backplain not completly out. Power up if it starts laoding the raid configuration,once the scan is complete it will give you a container not found error,now here is what you can do go in i think its control m or r,anyway look at the configuration and what raid you set it up for.write down the drive number 0-etc.ok the next move is the raid key a little device that sits on the motherboard beside the raid dimm reseat this,now you may want to replace the raid dimm or if you have a exact match for troubleshooting purposes you may try this.
Good Luck

Feb 05, 2009 | Dell PowerEdge 2550 Server

2 Answers

Problem with creating array


The Perc RAID controller in a 2600 doesn't support RAID 4.
You can do RAID 0, RAID 1 and RAID 5.

With 3 HDD's your best bet would be a RAID 5.

Mirroring is RAID 1 (which would only use 2 of the drives)

Aug 31, 2008 | Dell PowerEdge 2600 Server

2 Answers

Cant create additional raid


if there is a limit this would have been mentioned in the features of the product

please have a check

Aug 01, 2008 | IBM xSeries 226 Server

Not finding what you are looking for?
Acer Altos G510 Server Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acer Computer Servers Experts

rjivaro

Level 2 Expert

152 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Terry Allen
Terry Allen

Level 3 Expert

680 Answers

Are you an Acer Computer Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...