Question about Abit NF7-S V2 Motherboard

1 Answer

Every day at 1-st turning on all BIOS are in initial def. state.

I have a computer with Abit NF7-S v2 Motherboard and Athlon 3200 CPU and nf7d27s.exe reinstalled BIOS ver. 4.5....
Since I have installed this new version of BIOS computer can not load the Windows 98SE system, that is placed on the partition C: of the 1-st physical drive. But it normally loaded all others Windows XP systems that are installed.
But now every time after my computer in switching-off state becomes cool when I try to switch it on, all my pre-installed parameters of BIOS throw down to initial default states.
And every time I am forced to restore them.
What I must do to amend up these faults?

Posted by on

  • st_ilyja Mar 04, 2009

    I'm greateful for your advising though I have already coped with the second problem before than I've red it (by the simple replacement of the battery that supplies CMOS). But the first problem (with installation Windows 98 ) remains jet. I suspect, that before jet I have inadvertently corrupted MBR on the first physical drive. Besides that I have a problem with the second physical drive: when I boot up my computer from a DOS disket, the Partition Magic of ver. 7 nor of ver. 8 can not see the drive 2 (SATA disk, though drive 1 is a SATA disk too) . After booting with Windows XP both version of Partition Magic works normally.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I suggest you may try to check and replace the motherboard battery prior doing other procedures.

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Give me please BIOS mb Abit NF7 v2


http://majorgeeks.com/downloads25.html here you will find a vast array of bios tools hope this helps

Jun 17, 2011 | Intel D850MV Motherboard

1 Answer

I installed everything the CPU, RAM, and everything else. Connected all switches at the right places and the BIOS is on normal operation. I turn on the computer and its a blank screen nothing shows up....


ok, looking at the specifications All I can recommend is the following. double check the Video card to make sure it is properly seated and that it does not exceed the capabilities of the motherboard. 2 Disconnect everything from the motherboard except the CPU and case wiring/power supply and turn the computer on. If the system completes the post test, you will hear at least 1 beep and should hear several for the video card not being connected, then start installing components 1 at a time till you find the one causing the problem. Start with the Video card and then the ram as these are most likely where your problem is unless you have a faulty power supply which will be the problem if you don't get a completed post with nothing else connected.

Jun 18, 2010 | Abit IS7-V2 Motherboard

1 Answer

Abit NF7-s v2- hynix ram support problem


your system does not support the dual ddr ram unless you have a add-on VGA card

I have included the link to the user manual ... see chapter 1 section 1-1 Features and Specifications

Abit NF7-S v2


Supports DDR 400 only when using an add-on VGA card (NF7-M)

Feb 13, 2010 | Abit NF7-S V2 Motherboard

1 Answer

Abit NF7-s - hynix ram support problem


The problem probably is you mixing fsb speed, all the cards should
be pc3200 or all of them should be pc2700.

You don't mix.

Feb 13, 2010 | Motherboards

3 Answers

I need download drives of motherboard abit nf7-s2


Here is a link to a driver download:

http://members.driverguide.com/driver/detail.php?action=download&driverid=1270049

Jun 23, 2009 | Abit NF7-S V2 Motherboard

1 Answer

NF7-S2 No POST on startup. Can Not get into Bios


In that case the motherboard itself is faulty replace it..

Jun 08, 2009 | Abit nForce2 NF7-S2 Motherboard

1 Answer

Dont know where an item should go


This is an internal speaker. Find the speaker pins on the mother board. Should be somewhat close to the front panel connections.

Mar 23, 2009 | Abit NF7-S V2 Motherboard

1 Answer

BIOS error - CPU is unworkable or has been changed


try to reset cmos by removing CMOS battery from motherboard and reinsert again...

Dec 12, 2008 | Abit KV7-V Motherboard

Not finding what you are looking for?
Abit NF7-S V2 Motherboard Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Abit Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Are you an Abit Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...