Question about CB Radios

1 Answer

Microphone problem need to wire the microphone back onto the harness of my gme tx3200 electrophone as my kid pulled it off

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

WHERE I CAN BUY MIC OF CB TRC444 IN THAILAND

Posted on Mar 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to wire a 4 pin ProComm microphone to work on a 5 pin microphone for a Uniden Grant XL


The simplest way is to order a microphone adapter from ebay or a reputable CB shop. I have all my mics wired for standard 4 pin cobra. The standard 4 pin cobra is the most common and if you keep adapters handy then you can use all different kinds of mics on different radios.

Apr 09, 2016 | Uniden CB Radios

1 Answer

Does Motoroloa make a mic with controls in the head for the MCS2000?


It's very unusual to find a commercial radio with channel buttons on the microphone, however, with a bit of ingenuity, you should be able to do this. You need to connect two additional wires to the mic connector on the radio and replace the microphone with one that has the buttons. Connect each od these wires to the UP and DOWN buttons on the front panel. You will have to locate two pins on the mic connector that aren't being used. Usually there are a few available. You may have to disconnect two that are being used for the programming function if you don't have any available. This will have to be changed back to the programming function if you want to program the radio again. Connect the two wires in the microphone head to the up and down switches, and there you go. The other pin on the switches most likely connect to ground. You may have to get another mic cord if the one on your present microphone doesn't have any spares.

Dec 16, 2014 | CB Radios

1 Answer

Microphone wiring


the rf power going out is geting inducted on the wires of the mic.try using some ferrites close to the coax on the pl259 connector and on the mic wire itself.

Mar 01, 2014 | CB Radios

1 Answer

I disconnected and reconnected the cobra 29 nw ltd classic and now my voice is heard very low and slow it was working fine just before disconnection. can you help


How did you disconnect it?? Antenna wire?? Power supply?? Microphone?? May be that you have a short in your coax in back of radio. Try taking it loose and screw it back in. Try new coax. Turn up Mic gain knob or change microphone. Make sure power wires are connected RED to RED(+) and Black to Black(-). Try grounding radio to metal ; if inside house ground to metal water pipes, filing cabinet, breaker box or meter box or 8 foot rod into earth. Measure SWR it should read 1.1 to 1.5. Measure power supply with Voltmeter it should be 12 to 15 volts. Check antenna plug in back of radio is my guess or microphone itself.

May 09, 2011 | Cobra 29 LTD CB Radio

1 Answer

Microphone cord pulled out


If you know the model of your radio, this would help.....?

failing that just touch them on pins until it works, belive me if its just a straight chicken box you should be fine.....

May 15, 2010 | Uniden Bearcat Pro PC68XL 40-Channels Base...

1 Answer

GME Electrophone TX830N Dead TX


Either the microphone or RF Transistors are bad

Jan 30, 2010 | NorthPoint CB Radios

1 Answer

Wiring a midland 78/999 cb radio microphone


Pin 1 = white
Pin 2 = shield
Pin 3 = black
Pin 4 = red

Sep 27, 2008 | Midland 1001Z 40-Channels Base CB Radio

1 Answer

Microphone wiring diagram


What is the model number?

Sep 05, 2008 | Maxon CB Radios

Not finding what you are looking for?
CB Radios Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top CB Radios Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

489 Answers

Iron
Iron

Level 3 Expert

3018 Answers

Steve

Level 3 Expert

3287 Answers

Are you a CB Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...