Question about Daewoo DW500M Top Load Washer

4 Answers

E8 code when washer fills on front loader daewoo

E8 code when washer tries to get past the fill point, wont start washing or spinning but will drain, on front loader daewoo dwd-f1221....HELP desperate for someone to help solve, the powers that be dont seem to have any idea!

Posted by on

  • Julie Stone Feb 23, 2009

    not a DW500M Top Loader, is a DWD-F1221 Front Load.

  • Anonymous Apr 24, 2009

    I have Daewoo DWD-F1021 and it also give E8 code after filling with water. I have only had this machine for 3 years and this is the fifth time it has bee to mechanics for repair, different problems each time.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

E3 CODE WHAT MEANS

Posted on Apr 09, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Daewoo e8 - engine error! or Bad soldering.
Remove the control panel (the one in which many connections). Remove the rear rubber compound around contacts blue relay.
Resolder them. And it will be all ok!
Or - remove the entire back of the compound and look for where the bad soldering (cold soldering ). You can see it - blackened or exfoliated. Just solder all.

E8 code when washer fills on front loader daewoo - 12_5_2012_6_06_52_pm.jpg

Posted on Dec 05, 2012

  • sonny tee Jul 31, 2013

    Thanks rrromzes, this saved my washing machine. My symtom

  • sonny tee Jul 31, 2013

    symtoms were E8, intermittent drum spin, and intermittent water inlet. All seems to work now after fixing solder joints.

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

It could be the pressure sensor. If if never detects that there is enough water then it will never do anything else. The pressure sensor has an air small air hose that goes to a hollow, usually plastic cylinder that measures the pressure. Make sure the hose is securely attached on both ends. By the way, there should be a wiring diagram in the bottom of the unit for "service" point of view, but if you can follow a simple print you can read this. One end of the hose goes to a small electronic...sort of module...it has a cylinoid that will allow 115VAC to pass through or not. Generally, if it is not passing 115vac then it does not thing there is enough water in the drum yet. If you have a multimeter you could check the wires for 115 with the drum empty and full. If the 115 goes on and off then it gets worse because it is the main board. Hope that helps.

Posted on May 19, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The E8 error code has a simple fix.. change the carbon brushes, I had the problem and I do every 12 months or so, I make brushes at work (Mersen) and was able to manufacture some from grade Eg300 H, and get 2 spare, they cost around ZAR 150.00 around 10 USD.two screw to take the brush holder off the motor(tilt the machine on its side, against the wall) and work from the bottom of the machine.
E8 code when washer fills on front loader daewoo - 8_29_2015_12_37_12_pm.jpg

Posted on Aug 29, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer machine front loader wont fill up and wont drain


it maybe that the pump winding is open circuit some machines use the pump winding as the neutral line for the water valves so if the pump fails they wont fill no point in it filling if it wont empty

Mar 09, 2014 | Indesit W 123 Front Load Washer

1 Answer

Front loader won't spin and is filled up with water. Won't drain.


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning


heatman101

May 15, 2011 | Kenmore Energy Star 44092 Front Load...

2 Answers

Washer won't drain.


My washer fills up with water and goes thru the wash cycle but when it's time to drain, it just sits there and clicks.

Oct 17, 2009 | Tecnik TKL9260 Front Load Washer

1 Answer

Washer won't drain or spin


top loader ??? or front loader??? if top loader you have broken your lid switch, will fill, agitate, but when it comes to drain/spin for safety reasons if the unit doent recognize the lid closed it will not advance...if yo have a front loader then i would suspect that something has gotten into the pump assy and preventing drainiing of water therefore will not spin

Mar 02, 2009 | Kenmore Washing Machines

2 Answers

Please help me with my washer


Hello browneyez070
Welcome,

You said, your Hotpoint top loader washing machine won't spin water out. Model VBXR1O6OVOWW?

Common causes before considering repairs.

Water won’t drain
Drain hose is kinked or
Improperly connected on it.

Solutions
• Top of drain outlet should be less than 8 ft. above floor.
• Straighten drain hose and make sure washer is not sitting

Let me know if these measures help.
Huuum

Oct 15, 2008 | Hotpoint VBXR1090B Top Load Washer

2 Answers

My washer wont spin


Frigidaire front loader model # GLTF2940ES3.

Cycle ended prior to spin segment. Checked error code history to find E47 fault. Troubleshot per manual. Found that the "PTC one-spot check" read ~1582ohms. Although the book indicates that this is sufficient and recommends (rather tells) you to replace the control board we were still skeptical seeing as this is a ONE POINT check on a device that is non-linear. We went with the lesser of two evils. Purchased and replaced a new door lock. Works again! Phew, that could have been costly.

Aug 02, 2008 | Frigidaire GLTF2940ES Front Load Washer

2 Answers

Kenmore Elite HE3 washer keeps filling with water


The inlet valve will need to be replaced. Its a fairly simple procedure and a pretty inexpensive part.

Nov 15, 2007 | Kenmore Elite 45986 Front Load Washer

2 Answers

Washer repair


The transmission might have locked up causing the motor to overheat.

Nov 10, 2007 | Frigidaire FWS833A Top Load Washer

Not finding what you are looking for?
Daewoo DW500M Top Load Washer Logo

2,785 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

61292 Answers

Paul Bade

Level 3 Expert

1392 Answers

Are you a Daewoo Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...