Question about GE WJRR4170E Top Load Washer

1 Answer

Cold water is slow when filling for rinse cycle

The cold water is extremely slow when filling tub? Hot water comes in at a good rate when filling for wash Took off cold line and cleaned screen and ran water through it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GE Master
  • 3,361 Answers

Turn off the cold water.
Remove the cold water hose from the machine.
Look inside the cold water inlet on the machine and clean the debris from the screen.
Problem solved.

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 70 series washer


If you can see a constant water pressure from the hot and cold, chances are the water solenoid valves are ok.

I would look towards resetting to factory and checking the main control unit.

May 11, 2014 | Washing Machines

1 Answer

Fills to wash, drains but then tub won't fill for rinse cycle;


u need a new cold water valve, if u check the temp of the water while its filling it is mainly hot, or u have the hot nd cold hoses on the wrong way , as all rinses r cold

Jan 31, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Cold water filling of tub is extremely slow. No kinks


turn cold water off and remove hose from washer,next remove the screen from the water inlet and clean it and place it back in the valve, place hose back on the inlet,turn cold water back on and test cold setting,you should have good flow.

Dec 25, 2009 | Roper RTW4300SQ Top Load Washer

3 Answers

I can't get the cold water to fill the tub/rinse. the hot works.


Your problem is either a clogged COLD fill valve or a bad water fill valve. Turn the water off. Remove the COLD hose from the WASHER. Check the filter screen inside the valve for sediment. If you find sediment,remove the screen and clean it. Replace the screen and turn the water back on. If you do not find sediment on the screen,replace the water valve.

Sep 21, 2009 | Frigidaire FWS1339A Top Load Washer

1 Answer

No water enters on rinse cycle


I was partially wrong on my diagnosis. No cold water enters on either the wash or the rinse cycles. I also heard odd noises from the inlet valves. I realized the cold water valve was not opening. I've ordered the mixing valve and plan to replace it as soon as it comes in.

May 20, 2009 | Kenmore Washing Machines

1 Answer

Cold water Washes


It is normal for the machine to cycle between hot and cold water when filling even if selecting a cold cycle. The reason for this is because even a cold cycle requires the water temperature to be 78F for the soap to break up efficiently.

During the cold months the water in your pipes is probably less than 78F so the machine will need to add some hot water to bring it up to this temperature. Basically, it is adding cold and then hot water to maintain a temperature in the tub of 78F for cold water cycles.

Hope this helps, please rate my solution.

Apr 07, 2009 | LG WM-1832C Front Load Washer

2 Answers

Cold water will not stop filling during rinse


while the unit is filling in the warm cycle. reach behind and shut off the hot water tap.I bet the water flow stops filling, if so, you would need to change the inlet valve on the machine. You see, in warm, if the cold is not filling, you still hear the hot filling and the unit will advance. The rinse cycles are mostly "cold" only. if the valve is not opening it will not allow it to advance from the rinse section on the board.

Good luck!

Feb 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer won't fill in rinse cycle


REPLACE YOUR WATER INLET VALVE(HOT,COLD WHERE HOSES ARE)IT'S NOT OPENING ALL THE WAY TO LET THE WATER FILL UP FAST,LET ME KNOW HOW YOU DO-MIKE

Oct 19, 2008 | Maytag Washing Machines

1 Answer

Slow rinse cycle fill


take the hose off the cold water valve and check the screen on the water valve ,make sure the cold water is on all the way and the hoses are on the right valves get a water bucket hold the cold water line in it open the cold water valve to check the pressure

Jan 30, 2008 | Kenmore 98702 Stacked Washer/Dryer

Not finding what you are looking for?
GE WJRR4170E Top Load Washer Logo

Related Topics:

603 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...