Question about Kenmore Dishwashers

1 Answer

KENMORE ELITE DISHWASHER - MULTI-LIGHTS FLASHING

KENMORE ELITE DISHWASHER LIGHTS FLASHING - SMART WASH, NORMAL WASH, TIMER LIGHT ON, CANCEL DRAIN.
HAD A PROBLEM FEW WEEKS BACK WITH CLEAN LIGHT FLASHING RESET - SERVICE OUT - CLEANED PUMP - NOW THIS.

Posted by on

  • Anonymous Mar 12, 2014

    I have a Kenmore Elite Ultra Wash dishwasher model 665-1312. It will start and run normally until just after the soap dispenser opens. It will wash for another few minutes then stops, cancels itself and flashes the clean light. What can I do to fix it?

  • Anonymous Mar 12, 2014

    I have a Kenmore Elite Ultra Wash dishwasher model 665-1312. It will start and wash normally until just after the soap dispenser opens. It will wash for another few minutes then stops; cancels itself and flashes the clean light. What can I do to fix it?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 172 Answers

Look at your manual, usually available on net for reading or downloading. Blink lights are often used to code out a problem with various combinations and repetition rates to indicate trouble code number for look-up in manual.

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite dishwasher smart wash flashes


This sounds like a door switch that is faulty on your main door so the system gets a signal saying its not closed properly and there for signals fault

Dec 20, 2013 | Dishwashers

1 Answer

Kenmore elite dishwasher model 630 Smart Wash light is flashing


You may want to try:
Press a series of four buttons in quick succession. Press "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" to instruct your Kenmore dishwasher to run a short diagnostic test.
Wait for two minutes while your Kenmore dishwasher runs its diagnostic test.
Press the "Cancel/Drain" button once your dishwasher has completed its diagnostic test. This should reset your dishwasher control panel.
Check to make sure that there's no standing water in the bottom of your dishwasher. Standing water in your dishwasher may indicate that your dishwasher has stopped mid-cycle. You will need to press the "Cancel/Drain" button before you can reset your dishwasher control panel.

Dec 18, 2013 | Dishwashers

1 Answer

Kenmore 665 Dishwasher


Sound like you have a bad control console, which will need to be replaced.

Apr 08, 2012 | Kenmore 13742 / 13744 / 13749 Built-in...

1 Answer

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of...


Door latch.
Open and close the door to make sure the door latch is securely fastened

Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.
Some models have options that may require a water heating delay, such as Hi-Temp Wash, Hi-Temp Rinse, or Sanitize. Additional time may be required to heat the water to the proper temperature. The dishwasher will continue to circulate water during this heating delay but the timer will not advance until the proper temperature is reached

Oct 06, 2010 | Dishwashers

1 Answer

Kenmore Elite: Model 66576962K601.


I had exact same issue. I've called Sears Maintenance. They had to change 2 pieces in UI: Timer KUDS02SRB10 and CONSOLE Assy. Cost 360$ pieces  130$ Job Charge 60$ taxes.
Now It works perfectly, but I bought 1100$ 3 years ago... Really expensive to keep it running.

Nov 29, 2009 | Kenmore Dishwashers

2 Answers

Kenmore Elite Dishwasher clean light ind flashing and won't start


You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 17, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

1 Answer

Sensing light comes on and then the timer stop going down


I do nto have a solution- just the exact same problem. My machine gets stuck on 76 when doing a "normal wash" . last night I hit cancel and drain, then went to "time saver" and ran the wash and it seemed to work fine. Funny that both of our amchines stop at 76. Any ideas?

Nov 18, 2008 | Kenmore 24 in. 17482 / 17484 / 17489...

1 Answer

Stuck on wash cycle


Do you set your cycles by a manual timer or do you have a digital display?If a timer then it most likley bad or its stuck---if thats the case try wd40 behind it and see if it loosens,If your unit is digital then the control board is most likley bad,let me know.

Aug 05, 2008 | Kenmore 24 in. 15079 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,656 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...