Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

Frigidaire front loading washer stopped at rinse cycle. 3 beeps

Frigidaire front loading waher stopped at rinse /drain cycle. When I turned it off and tried to restart the rinse/spin cyle I get three (3) beep error code which states, "Drum overfilled." and suggests cause of problem to be, "Inlet valve or control board failure." Solution suggested; "Do not open door, select Drain/Spin to remove water, restart cycle." i followed these instructions. Washer drained some of the water and stopped again. Any further attempt to restart gives a hum, a 30 -40 second low noise and a stop. I have un-plugged the washer, even for one day, to clear any control board logic hung up but no luck. What is your suggestion? How do i determine whether I need a control board or an inlet valve? Where can I purchase either component and roughly how much?

My washer is barely 2 years old. Help!

Frustrated and disappointed owner.
George

Posted by on

  • Anonymous Mar 19, 2014

    this morning when we turned on the washer it started to make a clicking noise in the black box on the back of the washer (water inlet assembly) and hot water started to drain. After that we turned off the washer but the hot water kept draining.We turned off the hot water supply. We removed the back of the washer to inspect it. The drain valve was open.
    How can we fix this?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 50 Answers

When in doubt check the easiest thing to check. The pump can cause a number of errors to come up. Since the unit stopped in rinse I would start but checking to make sure there is nothing obstructing the pump before going to the expensive parts.

Posted on Feb 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer won't go into spin cycle, stops after final rinse. When I try drain &rinse it still will not spin.


If the unit does not spin correctly, this is usually an indication that the unit can also not drain. The unit will not spin if it senses a blockage or issue with the drain lines and/or pump. Try to check the drain lines in the back of the unit for any issue, and then see if you have an access panel to get to the coin trap or drain pump itself. Often socks and debris will clog up in this area and cause your problems.

Dec 25, 2012 | Frigidaire ATF6000ES Front Load Washer

3 Answers

Will not drain and spin keep beeping with error E20


  1. Remove the 2 screws on the bottom and the front access panel comes off.
  2. Pump is on the right, remove hoses from it, remove pump from machine and remove whatever is in the pump.
Try holding the start/pause and cancel key together for 3 seconds. The door lock, wash, rinse and final spin LEDs should light. Any error codes should be displayed when holding those keys.

Feb 27, 2011 | Frigidaire ATF6000ES Front Load Washer

1 Answer

My frigidaire front load washer will start a wash, complete the first cycle but then stop and flash all the lights and beep continously until I press "start" or "cancel". If I press "start" again it just...


Hello there:
If your cycle does not complete or The cycle doesn't advance
When the cycle should advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. than check the cold water supply line and the filter

Aug 15, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

F&P washer lights on and beeps


Clogged pump stopped up drain. If the washer does not think all water was pumped out in 8 minutes then it shuts down. Slow drain is my first inclination.

Dec 31, 2009 | Fisher Paykel EcoSmart GWL15

1 Answer

Seriously need help!!!


take off the bottom panel and look inside the cavity on the sidewall, there should be a plastic pouch stuck there, inside will be what we call a "tech sheet". it will tell what each error code means. i suspect that either the "coin trap" [from the tub to the pump] is plugged or there is something stuck in the pump. if the drain system is not working, the control board will not cycle to spin. it's kinda messy so lay down a lot of towels

Sep 24, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

My washer constantly beeps three beeps


3 Beeps/E30--Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Dec 27, 2008 | Kenmore 46462 Front Load Washer

1 Answer

Stopped during rinse/spin cycle


try removing the bottom front panel and see if there is something blocking the drain.

Oct 31, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Kenmore elite washer problem


sounds as if you have a drain issue, most common cause of fault is theres something stuck in the pump housing. remove the lower acess panel(3 screws along the bottom of the forn of unit) youll gain acess to the pump housing, remove the large cover to the "button trap" by uncscrewimg the cover, it will be righthin front of you in the center of machine when cover removed, im sure youll find your blockage within there

Oct 29, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Roper (Whirlpool) Washer


ohm out the lid switch, with the switch closed it should read contunity if it does not then the lid switch is the issue

Apr 19, 2008 | Roper RAB2121KW Top Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

489 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...