Question about Fisher and Paykel Washing Machines

1 Answer

HI WHAT IS CODE 62 AS AN ERORR MESSAGE - Fisher and Paykel Washing Machines

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Code 62 error message on this washer means that the "drain pump" current exceeds what it should be. Either the pump is faulty or (more expensive) the motor controller is faulty. Pump about $50.00, controller $300. Best of luck. 2TRP

Posted on Jan 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher and paykel intuitive wont spin or drain and hums buzzes and says code 62 needs service please help


Hi Tracy,
there are two reasons for a code 62, the first is the drain pump unit, it will not spin with water inside, the pumps likely to be blocked otherwise it will pump, stop, pump or pulsates.

Its been a while since I last logged on to here, have earlier post to describe how to check and remove the pump.
Seeing the machine has gone this far into the cycle then the second component the controllers has to be fine..

Good luck

May 09, 2015 | Fisher and Paykel Washing Machines

1 Answer

What's your question?I have washing matching hotpoint Aquarius wf360 with erorr code F-01


Motor triac problem. The triac would be in the unit that controls the motor speed.

May 04, 2015 | Hotpoint Washing Machines

1 Answer

What is the problem with my washer whan it has an erorr code CE ?


You have to tell us make and model to get a precise answer.

On many washing machines CE means communications error which is either a failure of the control board or some item controlled by the control board. It may be time to call the repair man.

Apr 18, 2015 | Washing Machines

1 Answer

Error Message


MY MACHINE IS PRO E 2 ERORR COM

Nov 23, 2013 | Daewoo DW500M Top Load Washer

2 Answers

Toshiba washing machine model AW 9790s error code E1


E1 is the drainage hose error, check the drainage pipe hose is not blocked damaged or filled with water or frozen, or maybe the return sensor for the hose is switched sensing something is wrong with the pipe but isnt. check the drainage hose ensure all water is out of the hose. open and close the lid one, then press the start/hold button this should reset the error alarm.

I hope this was useful

Feb 15, 2013 | Washing Machines

1 Answer

Erorr code -Err 1 is showing on our machine. Any ideas? Thanks.


Is this a Haier Washing Machine?
'coz I found an answer on their site..

"Q. The display shows Err 1. A. The door is open or not properly locked shut. Open and close the door, or firmly push the door shut until you hear a 'click'. If the problem continues, call the customer help desk or an approved service engineer."

Src: http://www.haier-uk.co.uk/support/faq

Hope this helps.. :)

Jun 09, 2011 | Washing Machines

1 Answer

Hi, I had a conversation yesterday but the expert is no longer responding to my emails. I have a Fisher and Paykel Intuitive Washing machine Model IW509AU which has a service code 62. Following directions...


Service manual for Fault code 62 says:
62. (00111110) Pump Over Current The Motor Controller module has detected an excessive pump current. Primary Source: Pump. Action: Replace Pump. Secondary Source: Motor Controller module. Action: Replace Motor Controller module.
You need to test pump resistance-should be approx 33 ohms. If pump tests OK, motor control module needs replacing. Not sure why you have been advised to check diverter valve. Sometimes both pump and motor control module need replacing, as the faulty pump blows the controller. But as the service manual states, the PRIMARY cause of this fault is the pump, so that's where you need to start. If you provide me with an email address, I can forward you the service manual for your model.

Mar 09, 2010 | Washing Machines

1 Answer

F-08 ERORR


Error code F08 indicates a sticking heater relay.
Check pressure switch- heater- and control module connections.
Worst outcome is you will have to replace the control module.
Please rate my solution.
Thanks.

Nov 20, 2009 | Ariston Technologies Washing Machines

1 Answer

Keep on getting the IE erorr


Error code IE means an water inlet error. Correct water level is not reached within 8 minutes after water is supplied or it does not reach the preset water level within 25 minutes.
Make sure water supply tap is open and not frozen. Check and clean water inlet valve from debris. If the issue persists, replace water inlet valve.

Oct 18, 2009 | LG WM1814CW Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

485 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...