Question about Gigabyte Motherboards

1 Answer

BOOTING PROBLEM MY PROBLEM IS AT THE BOOTING TIME THERE IS A MESSAGE DISPLYED ON SCREEN. THAT IS "CHASIS WAS OPENED GO TO THE SET UP AND CLEAR IT" PRESS F1 TO CONTINUE OR DEL TO SETUP.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 158 Answers

Hii, Go to the BIOS setting by pressing DEL at the system startup and then set it Default and then save setting.

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indicates chassis open when booting up


When the desktop case has been opened there is this notification when the computer boots up.
You can remove this message by going into the BIOS configuration and resetting this notification, this message will not appear again until the case has been opened again next time.

May 11, 2011 | Motherboards

1 Answer

System intruded, or tempered, or the chasis are opened before. please check the system


There is a chassis switch that detects when the desktop case has been opened. You can reset this switch in the BIOS configuration so that this message doesn't appear until the case is opened again.

Oct 31, 2009 | ASUS P4SE Motherboard

1 Answer

My system can not booting error message is chasis intruded fetel


KINDLY QUOTE THE EXACT ERROR MESSAGE YOU ARE GETTING. Start tapping the del / f2 key immediately after you turn on the system

Aug 26, 2009 | ASUSTeK P5K Desktop Board - Core 2 Extreme...

1 Answer

Error msg "The system chassis was opened" how to continue booting


firstly, you have to close the side panel after install any component. if the message show you again, try to find and short connect the jump (2 pins, signed Chassis) on your mainboard.

Feb 17, 2009 | Intel D945GCZ Motherboard

2 Answers

I installed 4gb of memory 4x1GB 240 pin and when booting up the computer recieved the decomplilation or disassembly prohibited.  What do I do?


HI there,

If you have installed the memory module correctly and are the right ones, than go into your bois and in there should be overwrite o clear this message.

Its only an alert message when you pc has been opened.

Regards,

Philip

Dec 06, 2008 | Dell Optiplex GX280 (99301) Motherboard

2 Answers

Error message


Open Your system and there is a Battery which looks like a Coin. that is CMOS Battery (CR2032) Change that battery and then Reboot your system and try go to BIOS menu with DEL , F11 , F1 or F2. Either of these Buttons can Work.

This will resolve your issue

Nov 26, 2008 | Motherboards

1 Answer

Sume time not booting os.then windows opening very slow


Hi there

you might have a failing hard disk or motherboard, try clear c-mos battery and try again . Also replace any faulty ram and other hardware that may cause the problem , unplug FDD, CD ROM and other devices , replace keyboard and mouse

Regards

Roger

Nov 12, 2008 | Intel D101GGC Motherboard

1 Answer

Error message


There is a micro-switch which detects when you remove the lid.
This can be disabled in the BIOS menu.
Switch on and press F2 or DEL key until you get to BIOS Menu (may ask for password).
Then find security menu and disable intruder alarm enable.

Aug 17, 2008 | Motherboards

2 Answers

Asus Board MOdel Number P4BGL (845 Mxl) is giving an error called Chasis opened or tampered.?


I read a solution of your problems, i did not ry this. But i want you to try in your motherboard: this was qoute by
" 9. anonobomber, 07-05-2002 09:51 read the manual from your motherboard, I'll quote it for you; Chassis Intrusion Lead (4-1 pin CHASSIS) This requires an external detection mechanism such as a chassis intrusion monitor/microswitch. The sensor is triggered when a high level signal is sent to the Chassis Signal Lead, which occurs when a panel or light detector is triggered. This function works with an optional ASUS CIDB chassis intrusion module (see your vendor for more details). If the chassis intrusion lead is not used, a jumper cap must be placed over the pins to close the circuit.
pinout 1[+5volt] [power supply standby] [chassis signal] [ground]
in order to supress the messages you are getting you will need to get a jumper to fit over the chassis signal and ground to bypass the chassis intrusion detection circuit.
This has nothing to do with resetting the CMOS. For board specific locations of the pins check http://www.asus.com.tw for the manual pertaining to your motherboard"

Jan 21, 2008 | ASUS P4BGL-MX 845GL (AS04P4BGL-MX)...

Not finding what you are looking for?
Motherboards Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gigabyte Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Tony

Level 3 Expert

2598 Answers

Are you a Gigabyte Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...