Question about NEC MultiSync VT440 Multimedia Projector

1 Answer

Nec projector vt440 wont turn on

Status lite on red power on orange whats up with it

Posted by on

  • Anonymous Apr 16, 2009

    same problem with indicator red lamp flashes, have to mess with button, green lamp to red lamp....?????

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 149 Answers

Hello. First check the lamp! From your description, it sounds like the projector is telling you that the lamp needs to be replaced. In "eco mode", when the power is green and the status is steady orange, that is the error message. In "high brightness mode" the status will be steady red. Hope I helped you.

Posted on Sep 09, 2009

  • Richard C Cohen
    Richard C Cohen Sep 09, 2009

    Blinking red (1 sec interval)--lamp or filter cover error
    Blinking red (8 sec interval)--fan error
    Blinking red (12 sec interval)--lamp error
    Blinking red (4 sec interval)--temperature error

  • Richard C Cohen
    Richard C Cohen Sep 09, 2009

    Hello again--added info you need...
    Steady red (High-Bright mode)/--lamp end of life
    Steady orange (Eco mode)--lamp end of life

    Blinking red (1 sec interval)--lamp or filter cover error
    Blinking red (8 sec interval)--fan error
    Blinking red (12 sec interval)--lamp error
    Blinking red (4 sec interval)--temperature error


×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause the status light to blink and the projector not turn on. NEC-NP50


Could be a bad power supply, or lose connection try another one

Aug 14, 2014 | NEC NP50 Projector

4 Answers

NEC VT440 projector problems can you help


Please check its vantilation fans, are they rotating or not?

Jul 24, 2008 | NEC VT460 Multimedia Projector

2 Answers

NEC lt240 lamp light stays off and power light is orange, no Image


COULD HAVE HOUR COUNT LAMP LOCKUP YOU WILL NEED TO RESET HOUR COUNTER BY USING BUTTON CONFIG AND MAINS.

john

www.jvsvisual.com

Apr 15, 2013 | NEC LT 240 Multimedia Projector

1 Answer

My NEC vt 595 was working fine last night and today i went to turn it on the status and power light started flashing red and orange and there is no picture


if Power is flashing orange - then it's cooling down

if Status is flashing red - then there are 4 flash combinations.
1 cycle (0.5sec On, 2.5sec Off) lamp cover or housing error
2 cycle (0.5sec On, 0.5sec Off) temperature error
4 cycle (0.5sec On, 0.5sec Off) fan(s) error
6 cycle (0.5sec On, 0.5sec Off) lamp error

Which is your condition?

Mar 18, 2011 | NEC VT595 LCD Projector

1 Answer

I have a NEC VT470 Projector. The power light is steady orange and the status light blinks red 6 times.


steady orange means projector in standby mode
red light 6 times is a lamp error.
either the lamp is old and wont start up or the ballast power pcb is not working.
can you hear the sparking of the high voltage trying to strike the lamp.
if you can then the lamp may be dodgy.
can you borrow one to test it out

Mar 02, 2011 | NEC VT470 Multimedia Projector

1 Answer

Turn on the projector the power light flashes green with status as green then it goes to a flashing orange light


there should be a status for the lamp light; check to see if this one turns red. If it does count the consecutive blinks if it is 6 then replace the lamp

Apr 15, 2010 | NEC VT800 LCD Projector

1 Answer

Status lamp blinking orange 6 times


PROJECTOR. NEC VT491 THE STATUS LIGHT IS BLINKING 6 TIMES RED, AND THE POWER LIGHT IS ORANGE

Jun 26, 2009 | NEC Multimedia Projectors

2 Answers

Reply to your question


One more question... when you plugged the projector in ac outlet, did it give smoke, smell or something?

Jul 24, 2008 | NEC VT460 Multimedia Projector

2 Answers

Lamp not lighting


Reset the lamp and try it.

Mar 28, 2008 | NEC VT660 Multimedia Projector

1 Answer

Status indicator blinks RED, not starting.


There are different rates at which the status light will blink to indicate various errors. See manual (link below) page 49 http://www.support.nec-display.com/dl_service/data/user_manual/ENGLISH/VT37/vt37_manual_e.pdf

Jul 29, 2007 | NEC VT37 Multimedia Projector

Not finding what you are looking for?
NEC MultiSync VT440 Multimedia Projector Logo

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Multimedia Projectors Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a NEC Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...