Question about Asrock P4i65G Motherboard

1 Answer

Wiring color code sequence for the pins to the front system panel for an asrock p4i65g motherboard. There are 4 double pin connectors. Jim/Sudbury

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

Can't say what the colours on your case wires are because they do vary but they should be marked up PWR SW (or PWR BTN), HD LED, etc.
Looking at the pin layout there should be a row of four with the pin on the far right missing and underneath a row of five with the last one on the far right being unused.

12 3 4
OOOO
5 6 7 8 9
OOOOO Pins 3 and 4 are PWR. Pins1 and 2 are PWR LED.
5 & 6 are Hard drive and 7&8 are reset

Posted on Jan 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pinout for power supply alesis 1622 p4


they have one already make 5 pin to 4 pin 3 dollars computer shop

Dec 20, 2013 | Asrock P4i65G Motherboard

1 Answer

Jumper setting vor motherboard setting in computer


AsRock Support > P4i65G > Main Support page,

http://www.asrock.com/mb/Intel/P4i65G/

In the top left column under the green AsRock name, click on - Manual in the list.

To the right of - User Manual - click on the country NAME nearest yours.

When the PDF file comes up........
Hover your mouse cursor at the bottom. The ghosted out navigation guide will appear.
Go to the far right, and click on the Adobe PDF icon.
(When you hover your mouse cursor over it, "Show Adobe Reader toolbar" will briefly appear)

Click on the Zoom Out icon ( - ) at the top, to Decrease the view size.
Use the Zoom In icon ( + ) to Increase the view size.

The Adobe Reader page number box, is to the right of the Down Arrow, at top.

Page 9 shows a Motherboard Layout, and the jumper locations.
Page 15 has the details about the jumper settings.

Motherboard installed in computer case;

A) At the Top/Left corner is PS2/USB/PWR1 jumper
There are 3 pins.
Starting on the LEFT side going towards the Right;
Pins 1, 2, and 3.

Jumper cap on Pins 2 and 3 for +5VSB
+5 Volt StandBy power.

It is for PS/2 or USB Wake-Up events.
Suggest leave on Pins 1 and 2.

B) To the Top/Left corner of the top white PCI slot, is the JR1JL1 jumper.
4 pins going across.

From the LEFT side going towards the Right;
Pin 1 and Pin 2 for JR1.
The next two pins are Pin 1 and Pin 2 for JL1.

If there is a jumper cap on those pins, your Front Panel audio ports, and Rear panel audio ports will not work.

(JL1 = Front Panel JR1 = Rear panel. The rear panel is also the I/O area. Input/Output. Where the mouse, keyboard, monitor, etc hook up)

C) Right below the round CMOS battery on the right side, is the
CLRCMOS0 jumper.
Clear CMOS jumper

NO jumper cap on those 2 pins to operate the motherboard.

"CLRCMOS0 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters.

To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from power supply.
After waiting for 15 seconds, use a jumper cap to short two pins on CLRCMOS0 for 5 seconds."

Regards,
joecoolvette

Jan 03, 2013 | Asrock P4i65G Motherboard

2 Answers

How to connect power to the front panel


Power to the Front Panel?

A) The plastic front of your computer is the Front Panel

B) The area of pins sticking up on the motherboard, that the wires from the Front Panel go to, is the Front Panel header.

I believe what you are requesting is the Front Panel header pinout.

AsRock Support > AsRock 775i65GV Motherboard > Main Support Page,

http://www.asrock.com/MB/overview.asp?Model=775i65GV

Go to the headings on the upper left side.
Products, Motherboard Series, 775i65GV, Overview and Specifications, and so on. Click on - Manual

On the next page go across from the heading - User Manual, and click on - Click Here, under the country nearest yours.

Disregard if you are aware;
This is a PDF file. The computer you are using now has Adobe Reader on it, which uses PDF files.
After you click it may take up to 30 seconds before the first page comes up.

At the top of the PDF file is the page number box. It is to the right of the Down Arrow.
You can use the Down Arrow to arrive at the page you want, or;

1) Put your mouse cursor in the page number box.
2) Left-click once. (Contents in page number box will be highlighted in blue)
3) Type the page number you want in the page number box.
4) Press the Enter key

Go to Page 10
This page shows an illustration of the motherboard, and as it sits in your computer case.
To the bottom Right corner is the Front Panel header. It is marked by the number - 16 [ System Panel Header ( PANEL_1) ]

{ It is the second header over from the Right side. It is Black in color. The first header is a USB header, and it is Blue }

Now go to Page 22. Front Panel Header Pinout. (System Panel Header pinout)

If you cannot download this motherboard manual, or if you do not understand the pinout;

There are 4 pins across the Top row.
There are 5 pins across the Bottom row.

The Top row of pins are numbered Even
The Bottom row of pins are numbered Odd.

Starting at the LEFT side going to the Right, on the Top row;
Pins 2, 4, 6, and 8.

Starting at the LEFT side going to the Right, on the Bottom row;
Pins 1, 3, 5, 7, and 9.

A) Pins 1 and 3 are for the HarDDrive Activity LED light.
Pin 1 is for the Positive ( + ) wire.
IF the LED light is dim when operating, switch the two wires around.

B) Pins 5 and 7 are for a Reset Switch, IF, a Reset switch is used.
Pin 5 is for Ground ( - )

C) Pin 9 is Not Connected. (N/C)

D) Pins 2 and 4 are for the Power On LED light.
Pin 2 is for the Positive ( + ) wire.
If the LED light is dim, switch the two wires around.

E) Pins 6 and 8 are for the Power On switch.

Page 21 details out the USB front panel headers, (USB 2.0 Header, Shared USB 2.0 Header), and the Front Panel Audio Header.

For additional questions please post in a Comment.

Regards,
joecoolvette

Dec 26, 2011 | Asrock 775i65GV Motherboard

1 Answer

Power switch


When looking at the motherboard, position yourself so that the RAM slots are running vertically on the right side of the board. The PCI and AGP slots should be running horizontally on the lower left side of the board.

In the bottom right of the board, you will see a block that has 9 pins, a row of 4 on the top and a row of 5 on the bottom.

The middle pins, one above the other, are the power button connectors. Insert your PWRBTN# on the top and the GND wire onto the botton pin.

May 01, 2010 | Asrock P4i65G Motherboard

1 Answer

Front panel to motherboard, ASRock P4i65G, connections


the power switch is on the 3 and 4 pins....the 7 and 8 pin are the reset pins. Trying it on wrong pins just won't startup the board but won't short circuit anything.

Jul 28, 2009 | Motherboards

1 Answer

Connecting front panel wiring to INTEL 845GRG Motherboard


Hello davideiker1, the Intel D845GRG MB manual is shared with another Intel board. (D845GBV MB). Go to this Intel site & download the D845GRG manual; http://support.intel.com/support/motherboards/desktop/d845grg/sb/cs-008873.htm You'll need Adobe reader to view the manual. Download Adobe from this link; http://www.adobe.com/products/reader/
See page 9 for motherboard layout.
The front panel connectors are shown on page 68, see item C.
On page 69 is, Table 31 shows the pin assignments for the front panel header. Front Panel Header (J9G1).
Pin 1 is power for the hard disk drive led, pin-3 is negative for the hard disk drive. Wire colors coming from the case are important. Look at all of the front case wires. The common color for each 2-pin connector will be ground. In most cases the ground wire is white, except for the internal speaker. Ground for the speaker is normally black. (This motherboards speaker is built into the MB, no hook up is needed).
Pin number 2 is positive for the case power led which lights up as green. Pin 4 is negative for the power led.
The reset switch is a bit different. Pin 5 is negative & pin 9 is positive, however if your case uses a two pin connector than connect pin 7 as ground & pin 9 for positive. The On/Off switch, pin 6 is positive & pin 8 is negative.
If this manual is not what you see on the MB, please advise.

Good luck davideiker1!
Need more information/questions post here.
Thank you for using FixYa.
Input, comments are welcomed.
Mike

Jan 22, 2009 | EliteGroup P6SET-ML Motherboard

1 Answer

New motherboard


You don't say what case you are using. If it is proprietary and the front panel header is all in one connector, you can carefully back the connector pins out of the block using precision screwdrivers. I keep a bunch of two pin connectors from junked machines so I can create individual connector sets when changing motherboards (eg, PWR SW, PWR LED, HDD LED and RESET). This also requires that you know the pinouts of both the old board and the new one so you can get everything connected properly.

Very doubtful you will ever find an adapter to change from one front panel block to another.

The 9-pin connector probably uses a spacer pin between the legs of the PWR LED, while it seems the 6-pin does not have RESET.

Dec 30, 2008 | Asrock P4i65G Motherboard

1 Answer

Swapped mother board


Hi Paul,
see page 8 number 15 for location. Than see page 19, System Panel Header in your manual.
The basic wire color's for positive are red, blue, green & can also be light blue, light green, light red.
Negative wires are usually white or black. Case wire colors do vary from case to case.
To see pin one shown on page 19, (positive + for hard drive led = HDLED+). Bottom row farthest pin to the left of set. Pin two is above pin one. Pin two is, PLED+ (known as power led). Pin 3 is to the right of pin one & is HDLED- (Hard drive led, negative). Pin 4 is above pin 3 & is also PLED-, (Negative for power led). ECT!
6781222.jpg If your new case has an internal speaker (Used for P.O.S.T, power on self test). This would connect to, Chassis Speaker Header located on page 8, number 16. Again, normally only two wires are used across the 4-pin connector. (One at each end of the connector).

To see ASRock's main site for the 775VM800 motherboard click this link:
http://www.asrock.com/mb/overview.asp?Model=775VM800&s=

Good luck Paul!
Run into a snag, just post the issue here.

Mike

Nov 02, 2008 | Asrock 775VM800 Motherboard

2 Answers

Asrock P4i65G motherboard/CPU


Hi Rlforeard, yes the BX80546PG3000E is compatible with the motherboard P4I65G.
http://www.alvio.com/product_view.aspx?product_ID=61048&source_ID=froogle
Here is the list from Asrock. CPU's supported for the Asrock P4I65G board. You will find you can go higher.
http://www.asrock.com/mb/cpu.asp?Model=P4I65G&s=478

Good Luck!
Mike

Jun 02, 2008 | Asrock Motherboards

Not finding what you are looking for?
Asrock P4i65G Motherboard Logo

541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asrock Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Are you an Asrock Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...