Question about Sunbeam 4237 / 4238 Iron with Auto Shut-off

2 Answers

My dual control sunbeam electric blanket flashes on one side

Posted by on

  • Anonymous Mar 20, 2009

    The cative likght flash in one side only

  • Anonymous Mar 18, 2014

    It is my sunbeam electric blanket

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Return this product as it is a fire hazard.

please mark this as a fixya! thanks

Posted on Mar 17, 2009

  • Joe Hogan Mar 17, 2009

    IF the blanket is new, return it as faulty. if it is old just trash it.

×

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

Ours did this when the plug from the controllers to the blanket was half unplugged - but I get could also be a bad element in the blanket. Be safe - get a new one

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to remove the top cover of a sunbeam CSP1 steam press to rplace the burnt out wires to the temp control .Any ideas Matt


The cover is held on by two screws underneath the top cover AND double sided stick tape, You have to remove the screws from the handle plastic knob. Also remove large knob for steam control pulling it up . Good luck domshea at aol.com

Jul 29, 2011 | Singer Electronic Steam Press Iron

1 Answer

How do I clean the Sunbeam electric iron, it has a "clean" button.


I found a manual at a different Web Site.
Thank you.

Dec 07, 2009 | Sunbeam Irons

1 Answer

Sunbeam Electric Blanket Model 972 A5 Type 692 (or 592) with temperature control 1 to 9 with 75 mins and 12 hrs and off control positions. The light blinks red and the blanket won't heat up. Please...


Did you get helped last year? If so please ignore. Otherwise....

Hi. You can locate a Sunbeam Service Centre via http://www.sunbeam.com.au/Pages/Support/Repairers.aspx

You're looking at $69,95 recommended retail.

BTW have you checked that it's not the blanket? Swap the controls over, if the problem follows the control it's the control. If the problem stays on the same side of the blanket, it's the blanket.

Also note Sunbeam has a 3 year warranty on electric blankets. If Date Of Purchase is less than 3 years ago call 1800025059 option 1 to speak to their Customer Service,

Apr 08, 2009 | Sunbeam 4237 / 4238 Iron with Auto...

3 Answers

Electric Blanket Control Blinks


mydual control sunbeam electric blanket blinks on one control

Dec 23, 2008 | Sunbeam 4237 / 4238 Iron with Auto...

1 Answer

Sunbeam 4267-000 not turning on just blinking red


"FF" or a blinking light will display meaning “Fault Found”. The “fault” is in the amount of power available to the blanket, mattress pad or throw.
There are several causes to this problem:
1. Bedding product is plugged into an extension cord, surge protector, power strip, or not plugged into a direct wall outlet.
2. Bedding product wasn't plugged in properly.

To FIX this problem, do the following to reset your bedding product:
1. Unplug the power cord from the electrical connection.
2. Unplug the cord from the actual bedding product itself.
3. Re-plug the cord into the bedding product. Make sure the connection is secure and complete.
4. Re-insert power cord back into a wall outlet.

If the 4 steps above are not followed in order, the bedding product will not properly reset.

Dec 08, 2008 | Sunbeam 4237 / 4238 Iron with Auto...

1 Answer

Fix a sunbeam iron


Hi,

Here is a tip that will help you to troubleshoot your iron and figure out what is wrong with it.

Electric Iron not Heating Up or not Working Right
http://www.fixya.com/support/r5300202-electric_iron_not_heating_up_or_not

heatman101

Sep 22, 2008 | Sunbeam 4214 Iron

1 Answer

Electric cord don't retract on iron model 4219.


I've contact Sunbeam and they're sending me a new iron.

Aug 18, 2008 | Sunbeam 4214 Iron

Not finding what you are looking for?
Sunbeam 4237 / 4238 Iron with Auto Shut-off Logo

895 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sunbeam Irons Experts

Tony

Level 3 Expert

2598 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Are you a Sunbeam Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...