Question about Goodman Heating & Cooling

1 Answer

Cannot figure out how to reset manual reset limit in janitrol goodman furnace model#gue060-3

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 700 Answers

Look around th3e burners for a limit switch with a red button that should be sticking out and reset it.

Posted on Feb 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Goodman furnace a36-20 fan runs non stop


is green wire from thermostat or from outdoor. retrace and change as needed. If not Goodman has a tech support number you can call while looking at unit.

Jun 21, 2014 | Goodman Heating & Cooling

3 Answers

1993 goodman status light 4 times blinking


Witch blower is running, the inducer or the systems blower?
System blower could mean the the high limit is opening and shutting down the systems gas train, I would check this out first.

The other problem could be with the pressure switch for the gas train, it is supplied from the inducer motor, check to see if it is operating fully.

HSI boards do go from time to time, this sounds more like a system control problem.

Jan 24, 2008 | Goodman GMS90703BXA Heater

1 Answer

Where is the reset switch on my Goodman CAPF036A2A?


Hi,
You can reset the controls by cycling the power off and then on again...

There also is a reset by the burner and one by the blower...push in the little red button in the center on the limit switch...


Here is a tip that will help you try to figure out why your furnace is not working.

Basic Furnace or Heating System Troubleshooting

heatman101

Mar 06, 2011 | Goodman GMS90703BXA Heater

1 Answer

I have JANITROL GAS FURNACE that the MAIN LIMIT


First, replace the limit. What causes a furnace to cycle frequently would be either a malfunctioning thermostat, a shorted thermostat wire, a bad control or the thermostats heat anticipator is not set right.

Jan 30, 2010 | Heating & Cooling

1 Answer

Janitrol gup power vent ignition sequence


inducer motor should run for several seconds before furnace lights, this proves the pressure switch and ensures proper ventilation

Sep 30, 2009 | Goodman Heating & Cooling

1 Answer

RED BLINKING (6TIMES) ON FURNACE


THE ROLL OUT SWITCH IS LOCATED IN THE BURNER COMPARTMENT MOST CAN BE RESET

Jul 20, 2009 | Goodman GMS90703BXA Heater

1 Answer

Goodman gas furnace


Sounds like it coud have been a flame sensor. the limit switch is usually near the top of the heat exchanger.

Nov 02, 2008 | Goodman Heating & Cooling

4 Answers

Goodman gmp075-3 led blinks 5 times


I Also have the same and other problems with my furnace model # GDS80703AXBB. First the LED kept blinking 4 times and I too jumped the primary limit, that didn't kelp. After several attemps I moved the wires going to the circut board and everything starting working again. After a week It stopped working again, so I pulled the plug out of the circut board checked all wires for for a bad connection plugged it back in. Now the LED blinks 6 times again I move the wires. Then the LED blinks 3 times. Then the transformer burns out. I have burned out 2 transformers and I have ordered a new circut board.

Oct 22, 2008 | Goodman GMS90703BXA Heater

2 Answers

Goodman GMP100-5 Rev Furnace Manual


I don't know where you are located, but there is a Goodman distributor in Sacramento, CA. Also in Ontario CA. They are a distributor so they may be able to help you or tell where to find someone who will help. Goodman is also known as GMC or Janitrol.

Jan 07, 2008 | Goodman GMS90703BXA Heater

1 Answer

No model number...


If this is a split system, look on the side of the furnace, no luck? remove the front panel. look for a little plate or sticker label inside there somewhere. If you are in California, there is a Goodman (A.K.A.) Janitrol, in Ontario CA. They may be able to help. (sorry don't remember phone #)

Dec 27, 2007 | Goodman GDS80904BNA Open Flame Heater

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

paulcarew

Level 3 Expert

2059 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Goodman Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...