Question about Samsung HT-Q100 System

1 Answer

Can't turn bass down

Bass very loud but can't see how to turn it down.

Tnanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I UNPLUGGED THE SUBWOOFER SO THAT JUST HAD THE TWO SPEAKERS PLAYING

Posted on Mar 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i get rid of jarring sound from my intex 4.1 hometheatre? the jarring sound peaks when i increase bass/main volume levels


You are approaching the cutoff level and getting distortion.
You you have too much amplification or too strong of input signal.

You can can turn down compression or turn up attenuation on the receiver and check other Dolby or neo settings from your manual. Or, don't turn it so loud.

May 08, 2014 | Home Theater Systems

1 Answer

To much bass and vibration


-5 decibels can be quite loud. Either turn down the bass, volume or both. The bass could be vibrating some items on a shelf or any other place. If you continue to play it that loud, you will more than likely, damage the amp.

Dec 19, 2013 | Home Theater Systems

1 Answer

How to open bose AM25 module


First thing -it is exceedingly difficult to get inside the wooden bass box to reach the woofer without seriously damaging the cabinet and virtually rendering the unit worthless. So if someone (like a toddler) has dropped a toy inside the box through the port and you're trying to get it out, better to buy one of those telescopic cameras ($200?) to look inside and attempt to fish it out.
However, if for some reason you are trying to get inside the power amplifier / EQ assembly on the back, this is possible to do without damaging the unit at all. I haven't done this in a while, so I am going from memory (please excuse any mistakes). First, with the bass module sitting upright on the floor and with the port facing away from you, examine the seam where the plastic cover to the amplifier/EQ meets the wooden cabinet. If you look carefully in that seam, you will see something that looks like the teeth of a gear. With a tiny screwdriver (or toothpick?), rotate that to the left (towards the side of the bass box that has the bass and treble controls) until a little triangle of plastic is sticking out and pointing straight up. Now, turn the bass box upside down and look at the place where all the cube speakers are plugged into. You should see two little black screws. Remove these and set aside. Now, stand the bass box on the floor, with the port facing down to the floor. With some effort, you should be able to simply slide the plastic cover off by pushing it from the "top", toward the "bottom". In other words, if the bass box were sitting in its normal position on your floor, you'd want to push the cover down, into the floor. I hope I'm describing it adequately...once you get it, you'll be pleasantly surprised how easy it actually is...and you can tell me if those two little black screws needed to be removed at all.

Oct 22, 2013 | Home Theater Systems

1 Answer

What is the measurment between the speakers in a 5.1 home theator for installation time


If you refer to the manual it will be explained. Generally, you have to compensate for two parameters that will vary with the distance and location each speaker will be relative to your listening position. Time delay and loudness.

If you don't compensate, each speaker's sounds from each will arrive at different times and your ear/brain will process the image unclearly and unconvincingly. An echo from behind you might arrive at the same tiome or before the primary event in the recording that created it, for example. The further a speaker is away, the quieter it will seem to be.

Then there's bass management. Using bass-deficient satellites requires the bass to be routed (managed) to a speaker that CAN handle it. This avoids speaker damage of the satellites and is, IMHO, a severe compromise in sound, or a victory of form over function for those who want minimum visibility from their sound systems. Contrary to the press regarding bass as being non-directional an explosion or other loud event from the rear of the room will not be convincing if the bass segment of it comes from in front.

May 27, 2011 | Sony HTSS360 Theater System

1 Answer

Why does my sharp cd-dvd500 shut off when too loud? How do i fix this?


Hi, you like your sound loud like I do-to prevent the stereo from shutting off simply turn the " BASS " control down a little- 1/3 to 1/2 of full should do the trick, write back to let me know if this helped, good luck and thanks for asking FixYa-Prodzilla.

Apr 20, 2011 | Sharp CD-DVD500 System

1 Answer

I have a problem adjusting bass and treble. I have too much bass when playing the TV so I adjust the bass down to get the proper balance. Then, when I play a CD, the bass is almost gone and I need to...


Figure out why the TV has so much bass. Look into its audio controls. I'd also consider attaching and listening to the TV-related audio directly and digitally through the Bose from the source(s) rather than through the TV and its questionable electronics.

Jul 15, 2010 | Bose 3 2 1 GSX System

1 Answer

How do i turn down my surround system on my


sure thing do you have your remote handy with ya and does you subwoofer have an adjustble nob on the back of it which will allow you to turn it down if not you need to adjust it through the receiver using your remote by going to the setup or menu

Oct 29, 2009 | Samsung HT-Z310T Theater System

1 Answer

Subwoofer Bass Level Problems


What is your sub stood on? If it is on a piece of furniture then this could be the problem. Bass frequencies travel further than higher frequencies due to their longer wavelength and will also be transmitted through any solid objects the speaker is in contact with. The solution is to mount your sub on a piece of foam to provide some damping.

Also if your sub has a port (a hole) on the back or side this needs to have a good 3 or 4 inches clearance from nearby walls or panels.

Finally the speaker cone itself needs to have a clear path to push sound energy into the room, if this path is blocked by furniture (some people like to hide them under tables) then it may make that furniture vibrate.

Nov 26, 2007 | JBL SCS200.7 Home Cinema Package System

1 Answer

SubWoofer


Sounds like your original and this sub have bad amps. The amp for the sub is not the same as the amp for the other speakers. The old unit has a dead amp and this new one is on the way out. (Pulling too much current on high bass)

Mar 30, 2007 | JVC TH-M505 System

1 Answer

Systems shuts off if sound gets too loud.


Yes, i had this same problem. If it was too loud, at level 37+, any loud boom would shut down the subwoofer, subsequently shutting down the speakers. As such, I figured it might have been the 8 pin dim cable, but that wasn't it. What solved the problem was lowerin the BASS level. Not the level on the subwoofer, but the actual BASS level. I had it at +10 (the max) and it was too much for the system to handle. I don't think I ever had it like that so I'm assuming someone, maybe my daughters, moved the settings. But anyway, moving the bass level back down to either 0 or +3 at most maintains the "boom" effect of the subwoofer minus the shutting off of the system.

Oct 20, 2006 | JVC TH-C60 System

Not finding what you are looking for?
Samsung HT-Q100 System Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Home Theater Systems Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Brandon M.

Level 1 Expert

34 Answers

Are you a Samsung Home Theater System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...