Question about Xerox WorkCentre XD100 All-In-One Laser Printer

1 Answer

H2 Blinking on the panel

I have a Xerox Workcentre 16fx that has been in storage for a while. I pulled it out and plugged it in. It powers up, but I have an H2 error flashing on the screen. Any ideas what that means?

Thanks!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Xerox Master
  • 4,338 Answers

Error code means that:
H2 Thermistor Open

Part #
Xerox Workcentre Pro 16FX, Xerox Workcentre XD100, Xerox Workcentre XD102, Xerox Workcentre XD103F, Xerox Workcentre XD104, Xerox Workcentre XD105F, Xerox Workcentre XD120F, Xerox XC1020, Xerox XC1040, Xerox XC820

Mfr Part #: RDTCT0128FCZZ


Xerox Workcentre Pro 16FX, Xerox Workcentre XD100, Xerox Workcentre XD102, Xerox Workcentre XD103F, Xerox Workcentre XD104, Xerox Workcentre XD105F, Xerox Workcentre XD120F

Mfr Part #: CTHM-0019DS52, CTHM-0019FC52

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem that the printer spooler is not displaying in the service. and when i add the printer then one message displayed that "your printer spooler service is not start. so what am i do for...


Hi,

Go to Start > Run, type in "services.msc", go down on the list till you see "Print Spooler", double-click, then click Start.

This should fix your issue.

Jul 22, 2011 | Xerox WorkCentre Pro 16fx Laser Printer

1 Answer

-Xerox workcentre m20i. -Yesterday turned machine


hi enviro,

so its the supply inside the Xerox is the next to be checked or fuse too..a technician nearest you can help open it.

mastergani

Jan 21, 2011 | Xerox WorkCentre M20 Black and White...

1 Answer

My xerox workcentre 470cx printer no longer power up when I plug it in the outlet. Can it be repaired?


Yes surely, only the power supply part of the printer is having problem, get it serviced by the technician.

Sep 05, 2010 | Xerox WorkCentre 470CX InkJet Printer

1 Answer

Loud clicking from the manual paper feed? very loud..? xerox workcentere pro 16fx


When printing from the computer, Clicking starts from the printer before printing starts.

Aug 11, 2010 | Xerox WorkCentre XD120F Laser Printer

1 Answer

HP Printer won't work with computer since reformat


When the system was reinstalled, the proper printer drivers probably weren't installed. Unplug the printer from the computer. Go to Start -> Control Panel -> Printers. If your Photosmart 2610 is there, right-click on it and select 'Delete.' Allow it to remove all associated driver files. Run the printer's setup CD. If you don't have the driver CD, go to this link: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=421139&lc=en&cc=us&dlc=en&lang=en&cc=us select your operating system and download the Full Feature Software and Drivers (hopefully you have a broadband connection). Run this setup program and follow all of the on-screen instructions. Do not plug your printer into the computer until instructed to during the installation.

This should resolve this problem. Happy printing!

Mar 19, 2009 | Xerox WorkCentre Pro 16fx Laser Printer

1 Answer

Xerox workcentre 470 cx problems


Those are referred to as the dots of death.
Most frequently the hard drive has failed.
Possibly firmware corruption or a main board failure. Normally not good.

Feb 23, 2009 | Xerox WorkCentre XD100 All-In-One Laser...

1 Answer

Xerox Workcentre M201 says open heat error


Fuser Error, Open Heat
Error, Heating Error and
Overheat
There is a problem in the
fuser unit.
Unplug the power cord and plug it back in. If the
problem still persists, please call for service.

Dec 09, 2008 | Xerox WorkCentre M20i All-In-One Laser...

3 Answers

Xerox workcentre m20i power off


First off try unplugging it and leaving it unpluged for 30 minutes. Not just turned off, but unplugged, then plug it back in and see if it works. There are filter capicitors in the low voltage power supply that sometimes have to sit with power removed for 30 minutes before they discharge and allow the power supply to turn on.
Sounds weird but I have seen it fix a dead machine probably 50 times or more. If that doesn't restart then you will have to replace the power supply. If that is the case let me know and I can tell you where to get it from and ho\w to replace it.
Try leaving it unpluged for 30 minutes. not less than 30 minutes.

Oct 16, 2008 | Xerox WorkCentre M20i All-In-One Laser...

1 Answer

Error mesage


NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.
  1. Locate the [C] (Clear) button on the Control Panel, at the far right.
  2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
  3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
  4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
  5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
  6. Press the [Start] button. The machine should be ready to use.
  7. Make a copy, to check that the machine is working properly
IF these steps do not work you will have to replace the fuser or fuser heat rod then perform the reset.

May 15, 2008 | Xerox WorkCentre Pro 16fx Laser Printer

1 Answer

Xerox WorkCentre XD100 Digital Copier


L6:The Main PWB sensed a Polygon motor lock signal error.

That is related to the mirror motor within the laser.
The laser most likely needs to be replaced.

Mar 12, 2008 | Xerox WorkCentre XD100 All-In-One Laser...

Not finding what you are looking for?
Xerox WorkCentre XD100 All-In-One Laser Printer Logo

Related Topics:

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Whit
Whit

Level 1 Expert

185 Answers

iteminconline

Level 2 Expert

110 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...