Question about Velodyne DD-18 Subwoofer

1 Answer

Connecting amp back to subwoofer on a velodyne spl 8

The 3 wires in ther back of the sub, how do they connect to the amp?
there's a J5 J3 and one other wire

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 124 Answers

You will need to contact Velodyne.

Posted on Dec 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On the back of the speaker has two wire hook ups do i bridge from one side of speaker too the other or is it left and right


Get the user's manual for hookup instructions. Don't bridge anything that you are not sure of. If you are referring to the speakers connections, they are used only if you do not have a sub out from the receiver.

Mar 09, 2010 | Velodyne SPL-1000 Subwoofer

1 Answer

Do you repair velodyne fsx 12 subwoofers


what is wrong with it ? is it the sub ? the sub surrounds ? the amp ?

more info please :)

Jan 27, 2010 | Velodyne SPL-1000 Subwoofer

2 Answers

I have connected the subwoofer to the pre-amp out



One of two things may be going on.

The amp has a fuse mounted on the PC board. The fuse may be blown.

The speaker may be bad. that may have blown the fuse.

You can test the speaker with a "D" battery.
Take the amp section out of the back, disconnect the speaker leads.
Touch the speaker leads to the poles of the battery. it should make a little thump and the cone should move freely.

Contact Velodyne for service.

Dec 21, 2009 | Velodyne CT-80 Subwoofer

1 Answer

Velodyne sub woofer: Series S Model: VA08BVX10


The volume control pot can be replaced.

Any good quality audio shop or electronics repair shop should be able to fix this.


Nov 17, 2009 | Velodyne SPL-1000 Subwoofer

1 Answer

SPL8R Velodyne sub - Same probelm


Go to the Velodyne web site and check the service center locations.

They may have one in your area.

It sounds like the amp may be the problem. That may be all you need to send.

Best bet, Contact Velodyne.

Jun 08, 2009 | Velodyne HGS-10 Subwoofer

1 Answer

No volume control on Velodyne SPL12BV sub amp


If my memory serves me on this amp, the volume control is actually a chip in the pre-amp section.

You could try and replace the actual knob on the panel and see if that fixes the problem.
If not, you will most likely have to send the amp section back to Velodyne for repair.

If you do send the amp back, use some masking tape and mark the speaker leads. Hooking these back up wrong will blow the driver and the amp.

Mar 26, 2009 | Velodyne SPL-1000 Subwoofer

1 Answer

When powered on speaker pushes all the way out


The problem is in the Amp. Velodyne is the only place you can get it repaired.

You will need to contact Velodyne for service

Mar 20, 2009 | Velodyne SPL-1500R Subwoofer

1 Answer

Hooking power amp to back of sub


Contact Velodyne.

Should have been a sheet in the box with amp for this

Feb 28, 2009 | Velodyne SPL800R Subwoofer Speaker

1 Answer

Velodyne SPL-1000 II subwoofer only snaps, pops and hisses


Go to the Velodyne web site, look under the support section and check the service center listings.

Also you could try the place you purchased the unit.

Dec 30, 2008 | Velodyne SPL-1000 II Subwoofer

1 Answer

How to connect pioneer reviever to velodyne subwoofer


Look for the sub pre out on the back of your amp and connect a sub cable to this and next to the LFE or phono type input on the back of the sub ,if it has two inputs left and right pick the left side ,set the cross over to suit your system and speakers,if you are not sure set the cross over to 80 hertz,this is a thx standard.
hope this helps.
CABLE GUY.

Dec 27, 2007 | Velodyne DPS-12 Subwoofer

Not finding what you are looking for?
Velodyne DD-18 Subwoofer Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Velodyne Audio Players & Recorders Experts

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Velodyne Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...