Question about Crane & Co Crane Plumbing 2386W Oval Whirlpool Bathtub, Biscuit

1 Answer

Pump does not start, it does have power

How many connections does the touchpad controller have. The tub is a crane 2386W whirlpool tub with a heat exchanger conected.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 125 Answers

Touch pads usually have three wires connected to a low water sensor (two wires) all running into a control box with a circuit board inside.
If you are in the tub and the tub is full of water and you then touch the 'pad' to turn the pump on and it doesn't turn on then the problem is most likely the box those wires and the pump plug into.
Get us that number off the box and we can solve this for you.

Posted on Feb 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pump hums but nothing happens


Sounds like the pump impeller is stuck. Shut off the power and check to see if the pump has a small round cover on the end opposite from the pump. Some pump motors have a slotted shaft that you can insert a screw driver and manually turn back and forth to loosen the stuck impeller otherwise drain the tub and remove the pump to access the impeller and attempt to free it.
Hope this helps.
Bob

Jun 01, 2014 | Crane & Co Crane Plumbing 2430W Whirlpool...

1 Answer

I have crane whirlpool tub model #2326WL51 needs new pump and touch pad


Need to know the model number of the pump in order to find the correct panel on the top of the tub.

send to: uspartscenter@gmail.com

Rod
US Parts Center

Apr 04, 2014 | Crane & Co Home

1 Answer

Pump will not turn on when button in tub is pushed


Check the pump outlet to see if it is tripped or the breaker if used . These are usually GFCI (Ground Fault Circuit Interrupter) type equipment and are very easily tripped.
Hope this helps.
Bob

Nov 03, 2013 | Crane & Co Crane Plumbing 2430W Whirlpool...

1 Answer

Whirlpool quiet partner iii pots & PANS LIGHT flashing


test the steps and fix it. God bless you


Heating Element

If lights are flashing on the control panel, the heating element might have burned out. The heating element heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element can be checked for continuity with an Ohm meter.


Enter your model number to see parts for your dishwasher.
Help me find my model number


Heating Element Assembly

If lights are flashing on the control panel, the heating element assembly might have burned out. The heating element assembly heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element assembly can be checked for continuity with an Ohm meter.


Enter your model number to see parts for your dishwasher.
Help me find my model number


Check Fault Codes

If the display lights are flashing and there is an error code in the display window, check the wiring diagram and tech sheet in the dishwasher that will provide information on the fault.


Drain Pump

If lights are flashing on the control panel, the drain pump might not be working properly. For two-wire drain pump motors check them for continuity using an Ohm meter. If it's defective You'll need to replace it. Drain pumps are not repairable.


Enter your model number to see parts for your dishwasher.
Help me find my model number


Touchpad and Control Panel

If the lights are flashing on the display the entire touchpad and control panel assembly might be defective. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced.


Enter your model number to see parts for your dishwasher.
Help me find my model number


Touchpad

If the display lights are flickering for no reason, the touchpad might need to be replaced. Sometimes when the touchpad is defective the display lights are flashing randomly.

Jul 22, 2013 | Dishwashers

1 Answer

A CRANE WHIRLPOOL TUB BOUGHT FROM MENARD'S IN THE 1990'S HAS TWO CONTROL KNOBS FOR AIR AS WELL AS AN ON/OFF BUTTON. WHERE CAN I FIND A REPLACEMENT SEAT THAT THE AIR CONTROL KNOB SCREWS INTO A


What you are looking for is called the wall fitting for the air control knob.
If you can email me a picture of the knob, topside and underside I can tell you who made it and if there are parts for it.
send your pictures to: sales@uspartscenter.com


Rod
US Parts Center
888-521-6183

Feb 10, 2013 | Crane & Co Crane Plumbing 2430W Whirlpool...

1 Answer

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the...


see this causes and fix it. God bles you
Check Fault Codes If the display lights are flashing and there is an error code in the display window, check the Error Codes guide on our website to determine which component has failed or is failing

Touchpad If the display lights are flickering for no reason, the touchpad might need to be replaced. Sometimes when the touchpad is defective the display lights are flashing randomly.

Touchpad and Control Panel If the lights are flashing on the display the entire touchpad and control panel assembly might be defective. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced.

Heating Element Assembly If lights are flashing on the control panel, the heating element assembly might have burned out. The heating element assembly heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element assembly can be checked for continuity with an Ohm meter.

Heating Element If lights are flashing on the control panel, the heating element might have burned out. The heating element heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element can be checked for continuity with an Ohm meter.

Drain Pump If lights are flashing on the control panel, the drain pump might not be working properly. For two-wire drain pump motors check them for continuity using an Ohm meter. If it's defective YOU'LL need to replace it. Drain pumps are not repairable.
10_3_2012_12_29_03_pm.jpg

Oct 02, 2012 | Dishwashers

1 Answer

I have a ies control box that its hard to find can you help me


Were you able to find a part? I have the exact same part in my hand that I am trying to replace

Jan 05, 2012 | Crane & Co Crane Plumbing 2386W Oval...

1 Answer

The clean light keeps blinking and won't run new cycle


Whirlpool & Kitchen-Aid
Tall Tub Dishwashers
PROBLEM: STOPPED RUNNING, WILL NOT START AND CLEAN LED BLINKS 7 TIMES, THEN REPEATS (WATER HEATING FAULT)
Control is programmed to stop running and not allow any further
cycles if it detects a water heating problem (no temperature
increase detected in heated Main Wash cycle or in 3 consecutive
cycles on the latest software version). Control blinks the Clean
LED 7 times repeatedly and disables the Start/Resume key until
cleared.
Running Diagnostics clears the control and allows it
to operate again. The water heating condition
must be corrected or the control will stop
running again. See potential causes below.
Check If…
Heater circuit problem:
♦ Open heater.
♦ Wire disconnected, open connection or component
in heater circuit.
♦ Faulty heater drive circuit on control.
Then…
1. Check operation of heater in Diagnostics cycle.
2. Unplug dishwasher or disconnect power.
3. Check resistance of heater and all components
and connections in the water heating circuit or heat
dry circuit.
Door switch not making contact consistently:
♦ Misaligned door latch assembly (which can be
aggravated by high door closure force keeping
strike plate from fully seating).
♦ Faulty door switch (high resistance).
♦ Loose or missing installation anchor screws,
causing tank to shift in cut-out.
NOTE: Neutral switch on plastic tub models is only in series with
the heater; other loads are not affected.
1. Unplug dishwasher or disconnect power.
2. Measure resistance of door switch contacts while
checking mechanical operation of latch assembly.
Confirm switches not loose from assembly. Check
strike plate and door closure.
Wash pump not pumping water past the heater efficiently.
• Foreign object in pump
• Excessive foaming
• Clogged pump screen or broken chopper screen
• Loose electrical connection in motor circuit
See Tech Sheet “WASH PUMP WILL NOT PUMP”.
Lack of water to heat. (Unit not filling properly)
• Insufficient water supply pressure
• Fill valve screen blocked or valve not opening fully
• Loose electrical connection on Fill Valve.
• Float switch obstructed or functioning abnormally
See Tech Sheet “WILL NOT FILL OR LOW
WATER”.
Diagnostic Key Dance:
Heat Dry - Normal - Heat Dry - Normal or
High Temp - Air Dry - High Temp - Air Dry

HOPE THIS HELP

Jan 24, 2010 | KitchenAid 24 in. KUDS01FLSS Built-In...

1 Answer

Whirlpool spa bath touchpad wiring


you need to acquire a wiring schematic from the manufacturer for your tub,....get all info you can think of i.e. model#, serial# name, etc. so when you reach a human on the phone, you can give them all of this required info they'll need to get you the right info you'll need to re-wire this thing,..good luck

Dec 17, 2009 | Crane & Co Crane Plumbing 2386W Oval...

Not finding what you are looking for?
Crane & Co Crane Plumbing 2386W Oval Whirlpool Bathtub, Biscuit Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crane & Co Home Experts

Dan

Level 1 Expert

19 Answers

cracklin joe

Level 2 Expert

105 Answers

bobalix

Level 3 Expert

447 Answers

Are you a Crane & Co Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...