Question about GE WSXH208A Front Load Washer

1 Answer

Model WBVH5200JOWW: Locked up. Unplugged waited,

Model WBVH5200JOWW: Locked up. Unplugged waited, plugged in again. No success. Anyone have a suggestion?

Posted by on

  • Anonymous Mar 10, 2009

    i heard big bangs during the spin cycle and then i stopped it and the door was locked??

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

We had the same problem. I found a site that talked about the drain pump so my husband took the front panel off and found the drain plug. Have a bucket and some towels handy, unscrew the drain plug, ours is right there when take the cover off and its white. Unscrew it slowly, water will most likely start draining. Our drain trap was completely full of lint, a necklace, coins, and stuff! Once we cleaned it out, plugged it back in, it reset itself and works like a charm. Good Luck

Tandy

tjwtaz@hotmail.com

Posted on Mar 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lg front load washer model wm2650h*a showed a power failure error so I cut it of cut it back on but it only stays on for a few seconds then cuts back off I reset the circuit breaker and tried it again...


Check the current rating of the breaker. how many other items are you using at the same time? UNPLUG all the items in the same room as the dryer. plug the dryer in and try to use it? did it trip again? if it did it shows the problem is with the dryer itself OR the breaker has developed a problem. Hope this helps

May 15, 2014 | Washing Machines

4 Answers

The lid lock light won't stop blinking.


LID LOCK FAULT
Fault is displayed if Lid Lock has not moved into locked position or motor cannot be powered.
Lid is not closed completely due to interference.
Check for lock interference with lock striker.
Wash media buildup (detergent, lint, etc.) is preventing the lock mechanism from sliding.
Main control detects open lid switch when attempting to lock.
Main control cannot determine if lid lock is in a locked state.

Perform the following checks if the washer does not lock (or unlock).
1. Perform the Lid Lock test under Manual Test Mode on page 9. The following steps assume that this step was unsuccessful.
2. Check lid lock mechanism for obstruction or binding. Repair as necessary.

Oct 20, 2012 | Whirlpool LSB6200KQ Top Load Washer

1 Answer

E:27 error code. Wet laundry is locked inside the washer. How can I get the door open manually? I've already unplugged the machine and waited and tried resetting everything.


E:27 message means that the door locking mechanism has malfunctioned and/or is overheating. Unplug the machine for 30 minutes and try again. If that doesn't solve the problem you need to call the service.

Mar 05, 2011 | Bosch WFVC5400UC Washer

1 Answer

I have a Kenmore Elite washer, Model 110.20096993, it starts beeping with about 10 mins left in the cycle and shuts off. Any thoughts?


I have the same model - it displays 10 minutes and keeps beeping in series of 3 (beep beep beep...... beep beep beep... etc..) ran through a cycle successfully but kept beeping like that the whole time. I unplugged it for 10 minutes but had the same symptoms after plugging it back in. I unplugged it for 24 hours, and that seems to have cleared the problem up.

Jun 12, 2010 | Kenmore Washing Machines

3 Answers

Won't do anything but hum....no lights on but door locked light


I cant understand what you are saying,your spelling didnt help much.If you re-write it again i might be able to help.

May 28, 2010 | GE WSXH208A Front Load Washer

1 Answer

WILL NOT START ONLY HUMS


Sometimes the control board gets locked up for some reason or the other, Try unplugging the unit from the wall and wait for a Minuit or so, then plug it back in, and retry.
If no success, then you will need to call a Repair company.

Good Luck!

Nov 03, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore He2Plus Washer: Controls Locked button lites up & beeps


plug it back in and there should be a buttong somwhere toward the corner and in small lettering"un-lock/lock" hold that button for 5 secs and see if it un-locks the board. if it dont the your board might be bad....hopefully this helps

Jul 30, 2009 | Washing Machines

1 Answer

My duet washer is locked and will not reset


To open the door,remove the bottom panel. Teach up inside on the lock side and find the pull ring. Pull on the ring while putting pressure on the door. It will open. Have the door lock wax motor and mechanism replaced.

Jul 17, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Affinity LTF7000ES door not staying locked


unplug the washer and wait 5 minutes before plugging it in again!
this resets the system. If this does not work then you may have a faulty door lock, latch, or switch!
An need hands on service on location

Thank You For trusting us with your question
Please remember to leave a solved rating before you leave!

Dec 31, 2008 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

The door is locked shut and the power will not go on


Now that you have plugged it back in, do any of the lights come on, any power? Or does the door just not open? thanks

Dec 15, 2008 | Washing Machines

Not finding what you are looking for?
GE WSXH208A Front Load Washer Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...