Question about Northern Tool 12 Room Purple Martin House

1 Answer

Diagram to repair onga house water pump - Northern Tool 12 Room Purple Martin House

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Got an Onga Riva-Flo water pump, model number TF30, its not working, can you suggests why and how to fix it please.

Posted on Feb 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Little Giant OPWG-71 after six months of trouble free use has stopped pumping my pond. It comes on, with no obstructions allows water to be pushed through it but won't pump. And yes even when


Hi don-eyre300.
Double check your suction side of the pump for obstructions if not then it is time to replace your pump...sounds like the impeller and housing is worn beyond repair.
Bud

Apr 20, 2013 | Fountains & Ponds

1 Answer

How do I take apart model PES-80-PW


nothing to take apart on this one it's a mag drive pump , if somehow the housing requires cleaning , backflushing down the outlet pipe is about the only way to do it , unit is sealed otherwise

mag drive means that a magnet is used to couple pump to motor so a direct connection is not needed so no drive shaft seals to fail , mag drives should never never be run dry with low to no water in pond , they use the water for cooling and will fail beyond repair if allowed to melt

Mar 31, 2013 | Little Giant Submersible Fountain Pump

2 Answers

Septic effluent pump loses prime


DONT TRY TO EMPTY THE TANK, RAISE THE FLOAT LEVEL. THIS STOPS THE PUMP FROM SUCKING AIR WITCH CAUSES THE PUMP TO LOSE PRIME,
WOW THAT WAS A EASY ONE. ....NEXT

OH AND YOU MIGHT NEED A CHECK VALVE ??

JAY THE POOL PUMP MOTOR REPAIR GUY LONGWOOD FLORIDA

Sep 11, 2012 | Monarch Pumps BE-S75 Wastewater Pump...

1 Answer

I'm not real sure but I think there must be a bearing or bearing housing broken I can't find it listed in the repair parts have any idea where to find this part?


The only bearings I can locate on the unit are built into the motor and its housing. Considering accessing them would damage the water tight seal I would not recommend replacement.

Mar 26, 2011 | Sunterra 3000 GPH Pond Pump 203000

1 Answer

Onga water pump for our bore. propeller on motor not moving unless you spin it manually to start


This is probally your start capicator on your motor. It stores extra power to start the motor and when the motor starts an internal switch lets it run on regular current. This is a cilinder ether on top of the motor or in the back of the motor. It's about the size of a"D" cell battery or a little bigger. with the power off you just pull the wires and put them back on the same place on the new one. Get the numbers off the old one and any pool shop or motor shop should be able to help you get one.good luck.

Jan 26, 2010 | Pentair Challenger High Head 1.5 Hp Pump...

1 Answer

How do you add oil to a sump pump? Do you add it to the water in the pit?


dont add oil to water-- if u have to or want to oil motor get a spray lube unplug unit and at bottom remove debris guard only clips on and spray shaft and behind impeller if need to lube upper motor bearing unscrew housing and carefully pull up enough to lube top of motor replace housing careful of watertight seals and test pump oil poured into pit would only be pumped out and does not contact motor which sits in watertight housing

Jan 25, 2010 | Little Giant Submersible Sump Pump, 1/4 Hp

1 Answer

House pressure water pump has to be reset to


it sounds like a relay for the auto shut off ....http://www.smarter.com/water-pumps/grundfos-mq3-35-3-4-hp-pressure/pd--ch-47--pi-11277834.html

Jan 16, 2010 | Grundfos MQ3-35 3/4 HP Pressure Booster...

1 Answer

The pump is not sucking up the water into the filter.


filter must be full of water to start.check that pump is spinning.check that suction tube is submersed & not too long some fish tank filters have a knob on top of the elbow between suction tube and pump housing,turn it back & forth to control flow.give the suction tube a wiggle where it meets pump housing.

Sep 24, 2009 | Tetra Second Nature 8.4oz. Desafin

2 Answers

How to Replace Little Giant Water Wizard Utility Pump Power Cord


Yes, If it goes together it will come apart. If it is the one I'm thinking of if you take the base apart there will be through bolts that run through the whole pump, remove these I want to think there are some that are short and these hold the base to the motor but they may be behind the impeller. Be warey as I'm not sure. But once the through bolts are out you should be able to carefully remove the top. Some have very frail gaskets here so be gentel. Once you have the top free there will be a compression nut holding the cord before pulling cord through use a light sand paper to clean the cord so the part you pull through will be fresh enough to seal. Don't lube the cord this will keep it from sealing. Pull it hrough and make your repair and put it back together the way it came apart. Use a sharpie to mark the top and housing as you take it apart. When finished loop some cord through pump handel and tie it off so this takes the weight in the future to keep from having the same problem again. good luck

May 29, 2009 | Little Giant Pool Cover Pump Water Wizard...

Not finding what you are looking for?
Northern Tool 12 Room Purple Martin House Logo

3,571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Northern Tool Fountains & Ponds Experts

Daniel

Level 2 Expert

123 Answers

nathan

Level 3 Expert

634 Answers

Jay Finke
Jay Finke

Level 3 Expert

1222 Answers

Are you a Northern Tool Fountain and Pond Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...