Question about RCA P52926 52" Rear Projection Television

1 Answer

Replacement power board

I had a bad picture it was concave and had red blue and green lines across the screen. The service tech. looked at it and the convergance board wasn't getting power. He ordered a new power board I put it in but the picture is the same. Is there a reset button or something i have to manually reset? We could not find a way to adjust the convergance on the menu screens is that possible to do on the tv in any of the menu options. I have a RCA HD52W59

Posted by on

  • Teddeebeer Feb 23, 2009

    All 3 colors are going from left to right in the center of the screen. I have had this TV for about 12-15 yrs and this is the 1st major problem. I dont want to spend alot and want to know how I can fix it. I would need someone to walk me thru where to look or send me a picture of what to look for.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 927 Answers

NEXT TO THE FLY BACK THERE ARE THREE, (CMT) FUSES THE CENTER ONE IS MORE THAN OPEN. THEY DON'T LOOK LIKE GLASS FUSES, THEY LOOK LIKE CM RESISTOR/CAP LIKE ITEMS. GOOD LUCK.

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Screen lookes like colores separating


Here's all I find regarding bad convergence from the techrepairCD:
RCA ~ITC222 D52W20~Convergence bad~~~ITC222~Replace leaky DL032 on
deflection board~~~~~~

RCA~D52W20Y ATC221~Convergence goes out/bowed after on for a few
minutes~~~ATC221~Problem may be on the deflection board. Was unable to
pinpoint where in this case.~~~~~~

RCA~D52W20BYX1 ITC222~Convergence way off after replacing small signal
board~EEPROMS were transferred over to new board~~~IK210 was
defective..transfer the new EEPROM back over.~Remember on these
sets*when replacing the SSB* if there is a small P on corner of
screen*hold volume on remote for 8 seconds after it reaches minimum.~~~~~

RCA~D52W20BYX1 ITC222~Can not align blue convergence* bottom really
bowed* possibly either color after replacing SSB.(Or no auto
convergence.~(Service menu: turn power off for 30 seconds* press vol dn
and ch dn* simultaneously for 8 seconds* set turns on with service menu
options)~~ITC222~In service menu* select convergence. If sensor
calibration was performed when convergence was too far off* it will not
alighn.~Get crosshatch with straight lines* perform sensor calibration*
then attempt convergence alignment again. Be sure to store settings*
then do sensor calibration again.~You must get a green flash of the
screen after sensor cal and a check in the box. RED flash indicated
convergence settings are too far off~~~~

RCA~D52W20BYX1 ITC222~no convergence correction~~~ITC222~LP650
(259271) DP670 (259246) & RP632 (259564) 4.7 3W on convergence power
supply board~~~~~~

Oct 28, 2008 | RCA R52WM24 52" HDTV Projection Television

1 Answer

Red, Blue and Green Ribbon on Tv


converence power supply board is the most likely problem

Jul 18, 2009 | RCA D52W19 52" Rear Projection Television

1 Answer

RCA 52 in HDTV red, green and blue colors not alligned - concave


That repair only repairs the issue of the convergence option missing from the on screen menu. If thats what your problem is then the ITC222A convergence option missing repair kit at the following link should repair the issue. The kit contains the fl231, DL231, CL230 and the CD with detailed instructions.
http://www.tvrepairworld.com/

Jul 17, 2009 | RCA D52W19 52" Rear Projection Television

1 Answer

Lots of Blue shadows off to side. concaved picture almost


HI, this is a failed convergence chip that is located on the convergence board. it will need to be replace ASAP. you can just replace the chip or , you can order a new board.

Replacing the chip can be a rough job if you don't have tech experience. if you are a fluid tech and you can solder and know your way around a circuit board, just replacing the chip will cost less. if you are not an experienced TV tech, i recommend a service call to the nearest TV tech to replace the convergence board.

May 20, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Green convergance wont adjust, bowed screen


Green really shouldn't be adjusted, you adjust red and blue to the green. When a color is bowed that indicates that a part or two are bad, probably the convergence output IC's and possibly a fuse or fusible resister. You may need a tech to come adjust it for you because after replacing IC's the adjustments should be done in the servicers menus not just in the consumers menus.

Mar 13, 2009 | RCA P52937 52" Rear Projection Television

1 Answer

The colors are distorted and it seems like the only colors that really show are blue, green, and red. When you turn the TV on you can see blue, green, and red lines across the screen. The picture also...


Hi there, this is what we call in the industry convergence board failure. this board regulate the rgb and keeps everything in order so the picture looks nice and clean. when this board starts to malfunction, what you are witnessing is usually the result. I suggest repairing this convergence board. this will fix the 3-d effect.

Mar 08, 2009 | RCA HDLP50W151 50" Rear Projection HDTV

2 Answers

Blue Flickering Screen - Which Repair Kit?


yes they provide a free service manual with their kits. the symptom of the blue screen could either be the signal or the FMT as they can both cause those symptoms, My professional guess would be the signal board as the FMT will cause distortion lines across the screen with no picture.

Sep 25, 2008 | Mitsubishi WD-52525 52" Rear Projection...

2 Answers

Screen lookes like colores separating


This is what is known as convergence. a projection tube ussally has three picture tubes.. red green blue. they all have to align. the concave picture indicates complete loss of convergence or convegence power supply. First question on these sets Do you have the convergence option in the customer menu under setup. if you do not this is a indication of the common "FL231 fuse problem" and inexpensive simple repair. I have wrote and artilcle on this under my tips and trick section. If you do have the option then next does autoconvergence work. in you case i would not think it work. under blue and red manual convergence does the crosshairs move. if not then this is indication of convergence power supply board. if they move at all this may indicate a convergence amplifer problem.

Sep 10, 2008 | RCA HD52W56 52" Rear Projection HDTV

2 Answers

Picture has 3 images, all different colors (red-blue-green) screen looks concave in the middle top & bottom


This is what is known as convergence..(very common)... first question DO you have the "CONVERGENcE" option in your setup menu?.... if you dont there may be a special fuse issue... if not then more than likely it is what is known as convergence power supply issue. you have complete loss of convergence?

Jun 01, 2008 | RCA D52W19 52" Rear Projection Television

Not finding what you are looking for?
RCA P52926 52" Rear Projection Television Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...