Question about Cisco RPS 22/18 (cab-rps-2218)

1 Answer

CISCO 2600 Router Troubleshooting

When I switch on the CISCO Router 2600, the response is that only the POWER and RPS LEDs become yellow - with the RPS LED flashing about once in one second. What could be the problem? Is it the power supply that has got a problem or the router itself?

Thanks in advance,
Medoma

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 44 Answers

This is the indicator configuration for the 2600, if the lights are yellow there is a problem.

The following indicator LEDs provide power, activity, and status information:
POWER (green)—Lit when power is on
RPS (green)
Off—No redundant power supply (RPS) is present
Blinking—System is booted, RPS is present, RPS failure
Continuous on—System is booted, RPS is present, no RPS failure
ACTIVITY (green)
Slow, steady blinking—System is booting
Blinks during system activity, such as interrupts and packet transfers
I suggest going to Cisco.com for full documentation on this product.

Posted on Mar 25, 2009

  • Tim Trimble
    Tim Trimble Mar 25, 2009

    I forgot to add:

    To tell what is going wrong, you need to connect a con cable to the unit before starting it, then start hyperterm on your computer set it to:



    Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, and no parity.



    This will give you a complete listing of what the unit is doing.

    If you don't have a com cable, they are available on ebay and many other sites on the internet for less them $20.



    Let me know if this helps...

    Tim

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need driver for cisco rj45 to d9


You don´t need a driver. You need a serial port on your PC/laptop and a terminal-software, such as Hyperterminal. Do not forget to set the terminal-speed to 9600 (this is standard on Cisco-routers).
hth, Karl

Feb 14, 2013 | Cisco Compatible DB9 to RJ45 Console...

1 Answer

Can I use Cisco interconnect SFP cable for Catalyst 3560 for connection two SFP-gigabit ports on Cisco Catalyst 3750?


While I am not 100% sure if you can or not, Cisco makes a Stack cable for the 3750s that is specifically designed to do what you are requesting. I recommend you get one of those instead. The SKU is CAB-STACK-50CM.

I hope this helps.

Jun 24, 2011 | Cisco Catalyst 3560 SFP Interconnect Cable...

1 Answer

Need driver for CISCO DB9 TO RJ45 6FT CABLE 72-3383-0 for my notebook


If I am understanding correctly, you are using a serial to ethernet cable. The serial cable plugs into your laptop and the ethernet end plugs into the CONSOLE port on the Cisco.

From here you use a terminal emulation program like "Hyperterminal" to connect via the serial port. As long as your serial port is installed, no other drivers are necessary.

May 02, 2011 | Cisco Compatible DB9 to RJ45 Console...

1 Answer

Router is not reading cable.


I'm assuming that you have it either connected to a computer and the wall properly. You may have to have some sort of machine working and connected to the router in order for it to acknowledge the cable. Make sure that everything is properly plugged in. Try and turning off your router for one minute and then give it another go. Try troubleshooting by unplugging and reconnecting wires to the router. Are you using a Cable or DSL Internet Service Provider?

Dec 24, 2009 | Dynex 7' Cat 6 Network Cable - Gray

1 Answer

Amber lights on a Cisco switch.


It sounds like you have loops in your topology. Loops will cause the LAN to crawl.

Amber, on a Cisco switch port means that a port has been blocked either as a security violation (if mac-address security is being used) or by spanning-tree protocol which shuts down ports involved in a network loop.

Check all your wiring carefully...especially the fiber-to-ethernet converters. If anybody has a hub or switch under their desk make sure they do not have two ports from that device patched into two ports in your cisco switch.

From Cisco catalyst 3500 user guide:

Solid amber

Port is not forwarding. Port was disabled by management or an address violation or blocked by Spanning-Tree Protocol (STP).

Note After a port is reconfigured, the port status LED can remain amber for up to 30 seconds as STP checks the switch for possible loops.

Nov 02, 2009 | Ortronics (MC62503)

1 Answer

Router portforwarding


Use the below website to configure your port forwarding

http://portforward.com/

Choose your modem type and application that u want to do port forwarding..

Aug 18, 2009 | Cisco CAB-OCTAL-MODEM (CABOCTALMODEMBXF)

1 Answer

How to connect CISCO CAB-OCTAL-MODEM ?


http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a008009428b.shtml

Above link goes through setup.

Jul 14, 2009 | Cisco CAB-OCTAL-MODEM (CABOCTALMODEMBXF)

1 Answer

V.35 Cable Local Loop


If your trying to establish a loopback for the Data Terminal Equipment, you seem to have satisfied the RTS/CTS, DTR/DSR loopback. At the V.35 end of your cable, you need to loopback the SD (balanced pairs) to the RD (balanced pairs), as well as insure that you have a valid clock source. Usually the DCE provides clock on a balanced pair SCT, SCR. towards the DTE. But, when you build a loopback cable or adapter, you can obtain clock from the DTE via the SCTE pair and tie it to the SCT and SCR balanced pairs. A lot of the requirements depend upon the DTE and DCE equipment your testing. Hope this helps...

Dec 09, 2008 | Cisco router cable, DB-60 male to V.35...

Not finding what you are looking for?
Cisco RPS 22/18 (cab-rps-2218) Logo

Related Topics:

624 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Network Accessories Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Vuk B

Level 3 Expert

678 Answers

kakima

Level 3 Expert

98608 Answers

Are you a Cisco Network Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...