Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool control locked

Was washing on bulky items cycle. When finished control locked button light was on.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Power shd be on. Press and hold "end of cycle" button for 3 seconds. Always wait for 2 minutes after the wash is over for the machine to release the door lock; an inbuilt safety device. Never force washer doors, you'll have probs.
Check out your filter too.

Posted on Mar 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Control lock light is on , toke door lock off once cleaned it put it back on and it worked now its on aagain and washer wont work


1 close washer door and dispenser drawer
2 select Clean washer cycle
3 Press start/ pause
The basket will rotate,then the door will unlock,lock again,then the cycle will continue
Water should come in and run a short sensing cycle about 3 minutes
4 This will determine item in the washer
a if no items are detected it will move to step 5
b if item are detected wash any control lock light will stay on door will unlock open and remove any garments
If b pessnpower to cancel f code then repeat 1,2,3
Once cycle begins allow it to finish
5 after cycle is complete leave the door a jar to allow for venting and drying of interior
Only use HE high efficiency detergent

Jul 05, 2015 | Whirlpool GHW9100L Front Load Washer

Tip

Hoe to unlock the controls of whirlpool washing machine


  1. To unlock the controls: Press and hold the End Of Cycle Signal button until the Control Lock light goes Off. To lock the controls: Press and hold the End Of Cycle Signal button until the Control Lock light comes On.

write_tip-sap4owyfpomquw3pehjkxnse-3-0.jpg


write_tip-sap4owyfpomquw3pehjkxnse-3-2.jpg

on Aug 24, 2015 | Whirlpool Duet GHW9150P Front Load Washer

4 Answers

How-To Unlock The Controls For A Whirlpool Duet washer


I have unplugged the machine and plugged it back in and restarted, just like when a computer needs to be reset/cold boot.

Jul 03, 2015 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

What will cause my Whirlpool washing machine to set on low speed spin cycle?


The machine uses automatic load sensors to balance the load and when you put something in the machine that is big, like a comforter, it knows that it cannot balance that item. So with a front loader it wont spin at high speed because it would be off balance and either damage the machine or the machine would "walk" because of the off balance motion.

Apr 28, 2014 | Whirlpool Washing Machines

1 Answer

Hi, After just finished washing one load, on


Hello & Welcome to FixYa


This is a common issue with Whirlpool Duet washer however; your washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE/CYCLE SIGNAL button for 15 seconds to reset the control. Please get back to me if you have any other questions.


Kevin

Aug 16, 2011 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

The load appears to have finished, but the CONTROL LOCKED light is on. The door is not locked and the washer is still full of water. Pushing cancel does not reset it.


Hello

This whirlpool duet front load washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE button for 15 seconds to reset the control. Please get back to me if you have any other questions.

Kevin

Nov 22, 2010 | Whirlpool Duet GHW9150P Front Load Washer

3 Answers

What does control lock mean?


This means that the machine will not respond to any controls and will have to finish its current programme completely before it will respond to any operator controls again. It is very useful to stop anyone changing the programme mid cycle. It also means that if the power is cut or you have a brown out that the machine will just carryon where it left off and finish the programme.

To unlock the Control Locked feature:

Press and hold the End Of Cycle Signal button for 3 seconds to turn this feature off.

When the machine is running and Control Locked light is on, the machine can be stopped by pressing the Pause/Cancel button, but cannot be restarted until the control is unlocked.

Oct 21, 2009 | Whirlpool Duet GHW9150P Front Load Washer

5 Answers

Whirlpool Cabrio WTW6600SW1: Won't drain


The washer drew half a tub of water on the "Bulky items" cycle, and stopped. All the lights on the cycle dial light up and flash, the machine beeps and the me error message in the "estimated time remaining" field is "Ld". I've tried to shut the machine down and change the cycle to "drain and spin" but it will not agitate, won't drain or spin.

Sep 05, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

2 Answers

Control lock is on but door opens it finished the cycle but the control lock wont shut off can you help thanks


Try some WD40 spray on the door
lock; on machine, not on door. And open & close for a few times with the power off.

Apr 13, 2008 | Whirlpool GHW9150 Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...