Question about Maytag Performa PAV2200

1 Answer

We have a maytag performa snd I need to replace the motor in dryer...dont know how to get to it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 117 Answers

In the seam at the top of the machine where the front panel meets the top lid housing, stick a putty knife in the center and slide it to the right until you hit the clip. Pull the putty knife out and then insert in into the clip liftingp on the top while doing to release. Do the same to the left side. Lift the top and then remove the inisde screw securing the front panel to the machine. The rest is a snap...

If I can help further, I am here....

Eric Campion

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a maytag performa dryer wont heat up sometimes


Hello there:
If there is no heat or heat sometimes please try these solutions
Heating element Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable. Thermal fuse On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.) Wiring A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.

Jul 14, 2010 | Maytag Performa PAV2200

1 Answer

Bearing on dryer motor sqealing. what to do?


LAT is a washer
Noisy motor need to be replace

Mar 03, 2010 | Maytag Performa LAT2500A

1 Answer

Maytag performa dryer suddenly stopped working, as if no power. i replaced both fuses and it worked. ran for about 15 mins and stopped again. any suggestions?


did it blow the fuses a second time.try this .put your dryer on a cycle that wont call for heat and turn it on.if the heat strips are not on and it still blows a fuse it is the motor.if the heat strips are on and it blows a fuse the heat strips are the trouble.

Nov 05, 2009 | Maytag Performa PAV2200

2 Answers

Dryer motor will not spin..motor sounds like it is sutck.


Get a putty knife, release the top by pressing the springclips between the front and top.
7ce3046.jpg

Then remove the front. The blower wheel may be the problem. They get loose.

Jan 04, 2009 | Maytag Performa PAV2200

1 Answer

Dryer won't turn on


sounds like the bearings on your motor are going bad

Dec 12, 2008 | Maytag Performa PAV2200

1 Answer

Maytag performa dryer vent got clogged and quit working


maytag performa dryer quit in middle of drying.

Dec 01, 2008 | Maytag Performa PAV2200

1 Answer

Maytag performa dryer vent clogged and dryer stopped


Hello,
I am not 100% sure I understand your question but if you need to know how to reassemble your dryer after cleaning it out,.use this link .. It has exploed views and parts lists .. http://www.pcappliancerepair.com/model-display.php
If my reply does not answer your question, please clarify your concern and I will assist you.
Regards,
Rick

Dec 01, 2008 | Maytag Performa PAV2200

1 Answer

How to get to heating element on dryer


the top will lift up put a putty knife in 2inches from the side and push in and release the tabs the element is in the back it looks like a spring

Nov 29, 2008 | Maytag Performa PAV2200

2 Answers

Quit working


This happened to me (as mentioned above) and I just need a new thermal switch. Easy to replace yourself.

Mar 23, 2008 | Maytag Performa PAV2200

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Al Clark

Level 2 Expert

290 Answers

Todd Marr
Todd Marr

Level 2 Expert

77 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...