Question about Optoma EP719 XGA DLP PROJECTOR 2000L 2500:1 CONT DVI-D WITH HDCP Multimedia Projector

1 Answer

Optoma EP719 Projector Won't Power Back On

I was getting ready to do a presentation and was checking to make sure everything was ok with projector and screen - it was. I powered the projector off until it would be time to start the presentation. When that time came the projector would not come back on - nothing! After finally replacing the bulb (very expensive), the projector did turn on but I was then having problems with it finding the components to the new lap-top I had plugged it into. I powered the unit off and re-connected it to my desktop computer and NOW, the projector will not come back on. This leads me to believe there is another issue other than replacing the bulb - can't afford to buy a new bulb and have it last only 15 minutes. Any ideas as to what my problem could be?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

When you first replaced the bulb it went back on and then later it did not. Most projectors have a safety switch that it is activated upon the bulbs cover placed. Once the cover is removed it activates the switch and shuts down power to bulb. It sounds based on your remarks, that this switch may have intermitten problems. I would suggest, locate this switch and verify its operation. Or, make sure the bulb cover is placed and/or secured properly.

Posted on Jul 10, 2009

6 Suggested Answers

webkruzer1
  • 17 Answers

SOURCE: My Optoma HD65 Projector stops starts working and

Possible cause is overheating.
Do you hear the fan working?
What happens when you use the lowest level light output?
Does it run longer?

Also possible cause is a faulty temp sensor.
AC wire connection may not be firmly pressed in socket.

Posted on Apr 09, 2009

  • 50 Answers

SOURCE: Optoma projector overheat issue - fan comes on but switches off

Most projectors have air filters. Yours may need to be removed and cleaned. No air flow = overheat.

Posted on May 28, 2009

  • 5 Answers

SOURCE: optoma ep719 will not power up

Try this:
There is a stuffed 10v 3300uf capacitor on the power board. You need to replace it.
Bellow you can check in the picture where the capacitor is located.
0f5b76c.jpg
Notice that in this picture I have already took the bad capacitor out and replaced with two small cords to reach the bottom and test the new capacitor.
To reach this place is not fast, several layers of plastic and metal must be removed, but is not a hard task to take the capacitor out and replace it for another.
It works just great! Now it is back on track with awesome image.

Posted on Oct 03, 2009

SOURCE: dvd10 optoma projector makes a loud noise

Hi, I'm not sure if it's the same problem I had..
I had it on picture mute, for maybe 15 mins, which may not have been a good idea. While it was muted, it made a sparking sound, and then a very loud grinding noise. When turned off, the lound noise stops, and the fan continues as usual for about a minute. As soon as it's turned back on, the grinding noise is back. But the logo seemed to display ok.

I took it in for repairs, and they said they needed to replace the color wheel to fix the problem.

optoma dv10 mode

Posted on Nov 03, 2008

  • 1 Answer

SOURCE: Power Point Presentation Using Sanyo Pro Xtra X Multiverse Projector

You have to ensure that the Laptop is feeding an image through the VGA port. The simplest way to do this is to press your laptop's Fn key and the CRT/LCD key (usually the F8 key) together. Also, you have to ensure that the projector is on the PC analog input mode.

Posted on Mar 20, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My image on my Hitachi 3lcd cp-x2515wn projector is upside down. Help!! Students are waiting!! :-/


try on the remote

menu - setup -mirror - v -invert

or
menu - main - mirror - v-invert

Jan 11, 2017 | Hitachi Office Equipment & Supplies

1 Answer

Can not make wifi connection with printer


If the printer is wifi ready, (you did not post the model number) then most of them require you connect them with a cable to the computer and set up the printer for wifi.

Jan 10, 2017 | PRINTER Office Equipment & Supplies

1 Answer

My Dell 3115cn printer will not connect to the network (it still works on USB cable), hard to believe it's broken, so can the printer system be reset?


Try turning off the printer and disconnecting power plug from wall. Hold power on button for about a minute. Then replug unit and turn power on - it should then attempt to hook up to your existing network.

If no go, try reinstalling the software that initially came with printer and was used to set up the network

Jan 10, 2017 | Dell Office Equipment & Supplies

1 Answer

My 202 doorbell does not "react" if the button is pushed AFTER my neighbor unlocks his car by using his remote key. Can I change the frequency range of the doorbell?


look for a cover that has small switches under it. You can change frequencies there. You must match the door button the same way .

Nov 19, 2014 | Office Equipment & Supplies

1 Answer

How to clean ink absorber for canon mp237


First of all open the ink cartridge of your printer.
When the ink cartridge would move all the way over, then disconnect the power cord of your printer.
Now pull the frame of rubber from the printer and remove ink pads.
To clean ink pads you may place them in a bowl having warm water and start rubbing and squeezing them to clean it from ink.
After removal of ink, keep the pads separate for dry.
When the pads get dry completely, place them back in rubber frame.
Reinstall the rubber frame in your printer.
For deep guide and support refer to-
Canon Pixma Mp237 Manual

Oct 07, 2013 | Canon PIXMA MP230 Multifunction color...

1 Answer

My DeVille 80 typewriter won't unlock and it's been like it for over 3 hours


Try to unplug for 30 min ,if still having problem go to mfg web site for instructions .

Feb 25, 2013 | Office Equipment & Supplies

2 Answers

Just bought and tried to load my Swingline Smart Touch low force stapler. Don't know how to get it opened


I have one of these models. Just push the gray lock mechanism at the end of the stapler and the loading magazine will pop out. The chrome plated magazine opens towrds the front....it slides forward and backwards.

Jun 17, 2011 | Office Equipment & Supplies

1 Answer

My fax wont work in my ricoh aficio 1515 mf??


Using the 1515 as a fax machine is a pretty simple procedure if everything works right. All you have to do is hook a working phone line up to the phone jack on the back of the copier (the one labeled LINE, not TEL).

Why won't the fax work? If it is giving you an error message, what is the message?

If you are not getting a dial tone when faxing, unplug the fax from the phone line and plug a working phone in, and see if the phone gets a dial tone. If it doesn't, there is a problem with your phone line.

You can also try plugging the fax machine into another phone line. If the fax works on that line, then there may be a problem with the first line.

Are you having problems sending faxes or receiving them, or both?

Jan 05, 2010 | Office Equipment & Supplies

2 Answers

HP printer psc 2210 all in one


Chances are that you didn't lock down the scanner when you moved the unit. You can attempt to open the unit and move the scanner bar manually to reset it. HPs are very difficult beasts when it comes to their power up check out. It must be fully functional...including all cartridges...to work in most cases. Good luck.

Dec 20, 2007 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

1,789 people viewed this question

Ask a Question

Usually answered in minutes!

Top Optoma Office Equipment & Supplies Experts

color wheel light...
color wheel light...

Level 2 Expert

137 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6393 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Optoma Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...