Question about LG WFT1071TP Top Load Washer

8 Answers

I'm using LG Fuzzy logic 6.5kg WF-S6607TC. After the water reach the level, machine start to spin for a few seconds and then stop.I can hear the peeping alarm and both wash & spin indicators are blinking.What is the problem?

Posted by on

  • 6 more comments 
  • AnkurJain Feb 22, 2009

    I am using LG Fuzzy logic 6Kg WF-S7012DN. When the program is started, the wash process is not happening as well as Wash and Spin starts blinking along with beep. Can anyone help?

  • slysamonte Apr 08, 2009

    I have the same problem. The machine just stops, beeps and blinks!

  • Anonymous Apr 19, 2009

    I have exactly the same machine and the same problem.

    The machine fills up and starts washing for a few minutes and the beep sound comes on and goes on until I turn the machine off.

    What should I do??????

  • Anonymous May 05, 2009

    Hi, I have the same problem with this LG WF-S6607TC. When it finished filling the water, it will wash for few seconds then it will stop, the machine will beep and some LEDs blinking. It seems cannot detect the closed lid anymore. I checked the warranty card and it already expired a month ago.

  • nafsat Dec 26, 2012

    Thanks jerryoah, I found that the megnatic was rusted. I replaced it and the Machine now working well.

  • jonathan aguilar
    jonathan aguilar Jun 14, 2014

    Hi, i have a problem regarding LG wf-t6560ct the otor will spin fo a few second then it will stop but it is spinning when drying clothes..

  • nitika
    nitika Jul 24, 2014

    Thank you so much for the lovely advise.

  • nitika
    nitika Jul 24, 2014

    Heelo nafsat. Just wanted to check from where did you manage to get that small and thin magnet?

×

8 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Check the lid cover. At the edge, there is a plastic housing some sort of a magnet. This is the magnetic sensor for lid cover open protection.
If the magnet is not there, place a magnet at the position on the washer where the housing will come in contact with the washer when lid is close.

Posted on Sep 09, 2009

  • 4 more comments 
  • torlitopilyo Apr 20, 2011

    thank you jerryoah! you're good! this advise is awesome! i initially couldn't bypass the washing machine sensor with the first few magnets i used (magnets on the back of refrigerator err...magnets?..lol)...eventually found a strong one (came from a broken computer hardisk...lol) that did the trick! thanks for this advise man! saved me time, hassle and money. -Marlowe from Singapore :D

  • torlitopilyo Apr 20, 2011

    thank you jerryoah! you're good! this advise is awesome! i initially couldn't bypass the washing machine sensor with the first few magnets i used (magnets on the back of refrigerator err...magnets?..lol)...eventually found a strong one (came from a broken computer hardisk...lol) that did the trick! thanks for this advise man! saved me time, hassle and money. -Marlowe from Singapore :D [i created an account in this website just to thank you. hehe] :D

  • yokeleetan May 16, 2011

    Wow that is great advise. For those who cannot locate the magnet, sometimes the magnet becomes rusty over time and drops off with the pathetic plastic housing. If you check the middle of the machine at the lid, you will see that there is a gap which is left by the magnet dropping off. if you can find the replacement magnet and stick it back on, that is great. if not you can place any magnet on the body of the washing machine where the missing lid magnet supposed to come in contact with the body. by sticking this magnet permanent on the body, the child lock function is gone, ie machine continue to spin when lid is opened. so use carefully if you got children at home as the machine now thinks that the lid is closed at all time.

  • nitika
    nitika Jul 24, 2014

    Please tell me from where can i get the new magnet?

  • Ed Silva
    Ed Silva Aug 30, 2016

    If you have a broken telephone, you can get the magnet from the speaker. take them off and stick in that empty section where the original magnet was.

  • Ye Thu Nov 29, 2016

    OMG.. saved my day!...

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I'm using LG Fuzzy logic 6.5kg WF-S6607TC. - 1_19_2012_2_30_28_am.jpg
A superfast solution when the lid is open,just put any magnet on the position shown in the picture ;)

Posted on Jan 19, 2012

  • 1 more comment 
  • Dany Daniel
    Dany Daniel Apr 07, 2013

    i have problem with WF-S6607TC when i start water level indicators blinking with beep .. magnetic lid censor is bypassed. till have same problem

  • nitika
    nitika Jul 24, 2014

    Saufi! Is it a stronger magnet than fridge magnet?

  • nishantha
    nishantha Apr 13, 2016

    Thanks bro! this is working for me. thank you very much!!!

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The disc in the middle came up after washing, I pushed it down, it worked fine for a few washes then it came up again. I don't know anything about washing machine, it may just need something to stabilise the disc.

Posted on May 04, 2014

  • zakir_yo Apr 11, 2016

    This worked. My LG washing machine, the water level indicator was repeatedly beeping and blinking. I tried pressing the disk, and it worked. Model LG WF-650. Thanks alot

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I got the same problem that first answer is the best answer but i solve this by different method first you have check about wire system because sometimes rats cuts wire and all of the stuff. Then open the back control panel area(where name and model type printed) there is a black colour little box, when lid open and close there is a connector with the lid and box. short both end of that little box and it will fix the all

Posted on Mar 18, 2016

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I tried one small fridge magnet without success; I tried another, slightly bigger, fridge magnet and that didn't work either. Finally I tried an even larger fridge magnet and it worked! Hurrah! Thank you so much

Posted on Sep 24, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I've got same issued, and followed your instruction. now it is working fine. thank all of you very much

Posted on Jan 03, 2015

  • Vakeesan Thevarajah
    Vakeesan Thevarajah Jan 03, 2015

    Did you replace the magent or short circuit the sensor inside ?

×

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I had the same problem (wash & spin indicators blinking & continuous beeping). So changed the magnet, but still it didn't work. I tried several techniques, but couldn't succeed. So I called a technician. He came and opened the control panel cover & repaired within two minutes. He charged me (LKR 2500/- in Sri Lanka, which is equivalent to 20 USD). Basically what he did was, there is a small sensor (little larger than the size of the magnet) which senses the magnet on the lid when the lid is closed. If the magnet doesn't come near the sensor, this sensor cuts off the power supply to the machine. Since this sensor wasn't working he just simply short circuited it- by passing the the power supply over the sensor. How to locate the sensor ? This small rectangular shaped beige colored sensor is located on the side of the mother board (when it's fixed in the washing machine's mother board cavity) very closer to the location where the magnet on the lid touches the operating panel.

Posted on Nov 26, 2014

  • Vakeesan Thevarajah
    Vakeesan Thevarajah Jan 03, 2015

    Hi Iroshan, Do you have the same problem ? What did you try ? Did you try to change the magnet or tried to shortt circuit the sensor inside ?

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, i have the same problem but the problem only occur when the machine trying to spin to dry the cloth. means washing and rinsing no problem, only when spinning(dry) after few sec it stops then thats it. but no peep sound or anything.

Posted on Jun 24, 2011

  • henry pisano Feb 21, 2013

    the machine has sensors to check the disposition of the load. try and check whether the load is equally distributed in the washing basin else it automatically senses the in distribution and stops spinning.hope it helps..pisano hm

  • Dany Daniel
    Dany Daniel Apr 07, 2013

    i have problem with WF-S6607TC when i start water level indicators blinking with beep .. magnetic lid censor is bypassed. till have same problem

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an LG Fuzzy Logic 4.5kg WF-452C Top loader. Put one load on and it worked fine. Went to put the second load on, and the water level lights are flashing and beeping, and the load won't start.


Take all the clothes outside put empty spin program if it finish without problem ur machine has no problem aftem u jusy check the inlet water filter and clean the filter every15 days,,

Apr 01, 2015 | LG Washing Machines

1 Answer

Hi I have LG Fuzzy logic WF-T6060NT top load water level all LED flushing simultaneously after pressing start button. Pls help confirm if the cause of this probelen is a defective control board.


Try unplugging it, waiting a few minutes, and then plugging it back in.

It may well reset the controller, and make the lighst quit flashing..

Jul 26, 2014 | LG Washing Machines

2 Answers

I have a LG fuzzy logic the problem is that its not stopping the water input its over flowing ....


When you press the "SPIN SPEED" button and "SOIL LEVEL" button the water level frequency should be above 246. If the water frequency level fails to reach 246 in 8 minutes you will get an IE error or inlet error. You would need to check the water valve, water pressure, etc.
How does the machine know if the water level is complete? Water level switch right? So obviously the control is timing the amount of time it takes till the water level switch kicks off. If it takes more than 8 minutes we have a problem don't we? Therefore if something is partially blocking the tubing from tub to switch that might throw off the water level switch. It is located on the main control assembly and has the rubber tube connected to it. The control board uses this to determine water frequency level. Just blowing the sediment out of that tubing will cure the IE error IF everything else mentioned is all good. I meself would do that first before replacing any parts.
LG WASHER MANUAL

Aug 04, 2012 | LG Washing Machines

1 Answer

I have a LG top loader Fuzzy logic 6.5kg model WF-T655th spin cylce not working, the light is flashing. I have a load in the machine, how do I emppty the water out of it. Have misplace the manual.


I have a LG washing machine WTF655TH, it has stopped working, its full of water, but when you push the one button, it trips, how do i get it working again

Jan 16, 2012 | LG Washing Machines

1 Answer

My LG washing machine model-fuzzy logic WF-s6607tc, is not spinning


The filter for your empty pump is probably clogged. The machine can't drain the water in the alloted time because it is draining to slowly through the clogged filter. The machine won't start the spin cycle if all the water hasn't been evacuated. You will need to find and clean out your empty pump filter (Probably behind a little door at the bottom of the machine.

Jun 23, 2011 | LG Washing Machines

1 Answer

Lg wf-s6607tc


This is probably a lid cover open protection. Check to see if there is a magnet on the cover, positioned almost to centre (slightly to the right) at edge of the cover. There is some sort of plastic catch to house the magnet. If it is not there, place a magnet at the corresponding area on the washer where the plastic catch will touch when the lid cover close.

Aug 16, 2009 | LG WFT1071TP Top Load Washer

2 Answers

I have Model WF-S6607?WF-S6607TC. Washing Machine. Loaded the clothes, pressed the POWER button, pressed the WATER LEVEL button, pressed the PROCESS button, and pressed the START/PAUSE button, But few...


This might be Lid cover open protection. There is a small magnet at the edge of the lid cover, housed in some sort of a catch.
If the plastic housing cracked, the magnet might have dropped into the washing drum. To overcome this, place a magnet on the position where the plastic catch will contact the washer when the lid is close.

Apr 04, 2009 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

Not finding what you are looking for?
LG WFT1071TP Top Load Washer Logo

7,462 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...